WinGD X72-B Operation Manual Download

Page: 221 / 526

Two more proximity sensors (002,

Figure 5-38

) are used to find the crank angle marks (004) for

TDC and BDC on the flywheel (003).

All proximity sensors are connected as follows:

•

First sensor pair to MCM-20 and CCM-20#1

•

Second sensor pair from CCM-20#2 to CCM-20#n

•

TDC and BDC to all CCM-20

Fig 5-38

Crank angle sensor unit on flywheel (example)

Legend

001

Cover

003

Flywheel

002

Proximity sensor

004

Crank angle mark

X72-B

AA00-9223-00AAA-043A-A

Operation Manual

Crank angle sensor unit

Winterthur Gas & Diesel Ltd.

- 221 -

Issue 003 2021-12

Summary of Contents for X72-B















































































































































































































































































































































































































































































































































Search results

Summary of Contents for X72-B

Reviews:

Related manuals for X72-B

Brands by name

Popular brands

WinGD X72-B, Operation Manual

Search results

Summary of Contents for X72-B

Reviews:

Related manuals for X72-B

Brands by name

Popular brands