Winkhaus STV AV2 Operating Manual Download

Page: 34 / 40

Page 34

Winkhaus STV

Oper

ating Manual EA

V 0124653 0505

Subject to technical changes

Winkhaus STV GmbH & Co. KG · Berkeser Str. 6 · D-98617 Meiningen · Germany · www.winkhaus.de · stv@winkhaus.de

Errors/Causes/Troubleshooting

Error

Indication

Possible cause

Troubleshooting

the door does not

lock automatically

hooked locking

tongue possibly not

locked

• the door is warped

• the contact pressure is too

high

• the door has not been

installed properly

• check the installation, if

required the strikes

• adjust the hinge plates

the latch is

“blocked”

the door is not

closed in the center

range

• the cut-out in the area of

the main locking house

is possibly not sufﬁcient

(dimensions see page 14)

• recut, if necessary

the door cannot be

closed

the tracer is “blo-

cked” at the single

strike

• the door sash has not been

mounted properly

• at the single strike



change the height of

the door striker (by using a

screw driver)

the motor does not

function although

voltage is applied

at the door

the door cannot be

opened

• no voltage supply via the

cable transition

• check the cable transition

(e. g. contacts, screwed joint

for KÜ-T STV)

the door cannot

be opened by the

motor

the motor does not

function

• power failure

• power supply is interrupted,

e. g. at the cable transition

• unlock mechanically via

proﬁle cylinder/handle or

lock via proﬁle cylinder

• check KÜ (correct the plugin

connection) or see above

the motor stops

• the door is warped

• the contact pressure is too

high

• the lock is too tight

• adjust the door

• check the soft movement

via proﬁle cylinder/handle

the motor functions

but the door cannot

be opened

• the main bolt is unlocked

via proﬁle cylinder

• draw the main bolt back

again via the proﬁle cylinder

Power failure

when/during:
a) the door is

locked

• the door can be operated

mechanically (proﬁle cylin-

der/handle)

b) the door is

open, lock is

unlocked

the door is possibly

not held by the

latch

• the motor is not in starting

position

• close the door by pre-

locking the main bolt, if

necessary

c) the unlocking

procedure

when the door is lo-

cked again, possibly

the M-hook, main

bolt do not lock

completely

• the motor is not in starting

position

• door can be operated

mechanically (proﬁle cylin-

der/handle), if motor has

returned to starting position



completely functions

6. Errors/Causes/Troubleshooting

Summary of Contents for AV2









































Search results

Summary of Contents for AV2

Reviews:

Related manuals for AV2

Brands by name

Popular brands

Winkhaus STV AV2, Operating Manual

Search results

Summary of Contents for AV2

Reviews:

Related manuals for AV2

Brands by name

Popular brands