SECTION 2
DRIVING YOUR MOTOR HOME
2-22
Crank the tire winch clockwise slowly, until
the room is fully retracted. Allow about 10
minutes to crank room in fully.
NOTE: Attempting to crank the room in too
quickly will raise pressure in the hydrau-
lic fluid lines and make cranking more
difficult.
Step 3 - Prep for Travel
·
Fasten slideout room travel straps. Leave the
hydraulic pump valve nuts loosened while
winch and strap are connected.
NOTE: Overtightening the valve nuts may cause
internal damage to the valves.
·
See an authorized Winnebago Industries
dealer
for service of the room extension sys-
tem before using again.
Bedroom Slideout Emergency Retraction
(Push-In)
In the unlikely event that your bedroom slide-
out fails to retract using the power switch, check
for obvious causes first, such as (in order shown):
·
park brake not applied.
·
low charge on house batteries (If this hap-
pens, press and hold the Battery Boost switch
on the dash in the ON position while pressing
the Slideout Power switch IN. This connects
the house battery to the chassis starting bat-
tery to provide auxiliary power to
·
blown fuse on chassis fuse block (#16-Step
Alarm or #24-Radio/Acc).
·
blown fuse on rear of leveling system control
pad (unfasten the control pad from the driver
side armrest panel to inspect the fuse)
·
See also “Troubleshooting” on page 2-18.
If you cannot find an apparent cause, call the
number on your Winnebago Industries Premium
Roadside Assistance card. They will dispatch a
service vehicle to your location to push the room
extension in so the coach can be driven to your
dealer for service of the slideout control system.
NOTE: The following instructions should be re-
viewed by the emergency service opera-
tor to become familiar with the bedroom
slideout “push-in” procedure.
“Push-In” Procedure for Rear Slideout
Rooms
·
Open the two hydraulic valves (with 1/4”
nuts on the ends) to relieve hydraulic line
pressure. (See Step 1 under “Slideout Room
Emergency Crank-In” on previous page.) DO
NOT LOOSEN NUTS MORE THAN 4
FULL TURNS.
·
Do not open any of the four T-handled valves
on the opposite end of the pump. These regu-
late the coach leveling jacks.
·
Apply a steady inward pressure of approxi-
mately 150 lbs. to the exterior sidewall of the
slideout room to push the room in toward the
coach until it is snug against the main coach
sidewall.
·
NOTE: Use some type of rigid, padded mate-
rial to protect the sidewall from punctures,
dents or other damage to the finish from any
device or equipment used to press the side-
wall in.
·
Pressure must be applied evenly to avoid
binding of the hydraulic mechanism. It may
take about 10 minutes to press the room ex-
tension inward completely.
·
When the room is snug against the coach
wall, close the hydraulic solenoid valves
(tighten nuts snugly) to prevent “creep out”
during transit.
·
See an authorized Winnebago Industries
dealer for service of the slideout control sys-
tem.
Further Information
See the HWH Hydraulic Room Extension operat-
ing guide included in the Owner InfoCase for fur-
ther instructions and troubleshooting
information.
Summary of Contents for 2003 adventurer
