Winterthur Gas & Diesel Ltd. X52 Operation Manual Download | Manualshive

Page: 159 / 519

background image

5.4.4.1

Local control panel

NOTE:

If a fault occurs in the remote control, which prevents engine control from the control
room, you can operate the engine from the local control panel.

The local control panel (001) has the electronic components that follow:

•

Local display unit (LDU-20)

There are two LDU-20 (002,

). One LDU-20 is installed in the local control

panel (001). The other LDU-20 is installed in the engine control room. The two LDU-20
operate independently from the remote control system. For more data about the LDU-20,
refer to

6.3 Local display unit (LDU-20) - general

•

ME tachometer

The ME tachometer (003) shows the engine speed in the ahead or astern directions.

•

Emergency stop button

NOTE:

Not all local control panels have an emergency stop button installed.

When you operate the emergency stop button (not shown), the engine stops immediately.

The fuel pressure control valve (PCV) releases the pressure in the fuel rail. At the same
time, the fuel pump supply decreases to 0 (zero).

○

For data about the PCV, refer to

5.5.4 Pressure control valve

○

For data about engine stop, refer to

8.15 Stop the engine

•

Telegraph receiver

The telegraph system is part of the propulsion control system, refer to

6.1 Engine control

.

X52

AA00-4618-00AAA-043A-A

Operation Manual

Local maneuvering stand

Winterthur Gas & Diesel Ltd.

- 159 -

Issue 002 2018-11

«
...
157
158
159
160
161
...
»

Summary of Contents for X52








































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X52

Brand: Keithley Pages: 149

Brand: Makita Pages: 8

Brand: VECTECH Pages: 5

Brand: Dana Design Pages: 20

Brand: Federal Signal Corporation Pages: 2

Brand: Harman Kardon Pages: 7

Brand: Federal Signal Corporation Pages: 12

Brand: IDEAL Pages: 12

Brand: ParaBody Pages: 6

Brand: ParaBody Pages: 11

Brand: Safavieh Pages: 2

Brand: Vendlet Pages: 2

LED Street Bar 16x3W RGB IP65

Brand: Varytec Pages: 9

Brand: VARILITE Pages: 8

EVENTPROFILE VL800

Brand: Vari Lite Pages: 34

Optica 30 Series

Brand: Varex Imaging Pages: 36

Brand: VARISCO Pages: 24

Brand: Vari Lite Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands