Winterthur Gas & Diesel Ltd. X52 Operation Manual Download

Page: 30 / 519

1.6.4

Designation of the four sides

WinGD uses the designations of the four sides of the engine as follows (refer to

Figure 1-1

and

Figure 1-2

•

DE - Driving End (open short side with flange to the propeller shaft)

•

FS - Fuel Side (long side with supply of fuel and other operating media)

•

FE - Free End (closed short side)

•

ES - Exhaust Side (long side with discard of the exhaust gas and supply of scavenge air).

Fig 1-1

Outline drawing - long side (generic)

n-1

004

003

001

002

Legend

Free end

Driving end

001

Turbocharger

003

Flywheel

002

Auxiliary blower

004

Supply unit

X52

AA00-0000-00AAA-018C-A

Operation Manual

Conventions

Winterthur Gas & Diesel Ltd.

- 30 -

Issue 002 2018-11

Summary of Contents for X52








































































































































































































































































































































































































































































































































Search results

Summary of Contents for X52

Reviews:

Related manuals for X52

Brands by name

Popular brands

Winterthur Gas & Diesel Ltd. X52, Operation Manual

Search results

Summary of Contents for X52

Reviews:

Related manuals for X52

Brands by name

Popular brands