Winterthur Gas & Diesel Ltd. X52 Operation Manual Download | Manualshive

Page: 486 / 519

background image

12.11.8

Fuel Additives

WinGD does not recommend the use of fuel additives. Additives are not necessary for fuels that
obey the ISO 8217:2017 standard or for fuels that WinGD has recommended.

If you think, that it is necessary to use additives, WinGD recommends to speak to the fuel supplier
and to the additive supplier. They can give you the related results of the use of additives. If you
use additives for some causes, you get the full responsibility. Existing No Objection Letters done
by Wärtsilä Switzerland Ltd. are no longer applicable and have no more support by WinGD.

NOTE:

WinGD does not accept liability or responsibility for the performance or potential damage
caused by the use of such additives.

12.11.9

Non-standard fuels

If it is necessary to use non-standard fuels (fuels that are not in the related list from WinGD), speak
to or send a message to WinGD before you use it.

NOTE:

WinGD does not accept liability or responsibility for the performance or potential damage
caused by the use of non-standard fuels.

X52

AA00-0000-00AAA-030A-A

Operation Manual

Diesel engine fuels

Winterthur Gas & Diesel Ltd.

- 486 -

Issue 002 2018-11

«
...
484
485
486
487
488
...
»

Summary of Contents for X52








































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X52

Brand: GE Pages: 138

Movie FL Black E27 Flaps

Brand: Qazqa Pages: 2

Brand: Cadex Pages: 300

Brand: Federal Signal Corporation Pages: 2

Brand: Harman Kardon Pages: 7

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 20

Brand: Eaton Pages: 24

Brand: Wacker Neuson Pages: 34

Brand: Martin Pages: 202

Brand: xsto Pages: 63

Brand: Gomaco Pages: 30

Brand: Panduit Pages: 4

Einthoven CR1000

Brand: ACE Solution Pages: 29

Brand: Lutron Electronics Pages: 10

Brand: Mikrona Pages: 12

Brand: Mark Fitness Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands