manualshive.com logo in svg

Wintex Agro 2000, Instruction Manual

The LG 2000 User Manual is an essential guide for operating and troubleshooting your LG 2000 product. Download this manual for free from 88.208.23.73:8080 to ensure you maximize the full potential of your device. This comprehensive manual provides step-by-step instructions and valuable insights for a seamless user experience.

Share
Download
background image

P A G E

 | 

2

 

 

 

 
 

 

Wintex Agro, Vilhelmsborgvej 8C, DK-7700 Thisted 

+45 97990800, contact@wintexagro.com, www.wintexagro.com

 

 

 
 

 
 
Manufactured by:

 

WINTEX AGRO 

 

Vilhelmsborgvej 8C 

 

DK-7700 Thisted 

 

Type designation:

 

WINTEX 2000 

 

Voltage:

  

12 volt DC 

 

Year of production:

 

2019 

 

 
 
 
 

 

 

 
 

 
 
 

 
 
 

 
 
 
 
 

 
 

FOR YOUR SAFETY 

 

Before starting

 the WINTEX 2000 please make sure that nobody is present within a range of 10 meters. 

 

When inspecting the WINTEX 2000, you must always activate the emergency stop, and the ATV must be turned off. 

 

Every time

 you start the WINTEX 2000, you must 

test the emergency stop

. If the emergency stop does not turnoff the soil sampler, you 

must not use it. 
 
The WINTEX 2000 has sliding and rotating parts. Keep your limbs away from the soil sampler unless it is turned off, and stay away 
from the foot / the base of the soil sampler. 

 
 

 

Summary of Contents for 2000


















Reviews:

No comments

Related manuals for 2000

Airmetrics MiniVol Operation Manual preview
MiniVol
Brand: Airmetrics Pages: 56

Brands by name

Popular brands

Load more brands