manualshive.com logo in svg

Wintex Agro 2000, Instruction Manual

The LG 2000 User Manual is an essential guide for operating and troubleshooting your LG 2000 product. Download this manual for free from 88.208.23.73:8080 to ensure you maximize the full potential of your device. This comprehensive manual provides step-by-step instructions and valuable insights for a seamless user experience.

Share
Download
background image

P A G E

 | 

8

 

 

 

 
 

 

Wintex Agro, Vilhelmsborgvej 8C, DK-7700 Thisted 

+45 97990800, contact@wintexagro.com, www.wintexagro.com

 

 
 
 

ADJUSTING THE PRESSURE OF THE PROBE 

 

 

Loosen the lock nut. Adjust with a 6 mm hex key. Pressure will rise when turning to the right. 

 

Lower the pressure by turning to the left. 

 
 
 

 
 
 

 
 

 
 
 

Depending on the vehicle’s weight and the kind of soil, the pressure must be between 10 and 30 bar.

 

 

Read the pressure on this manometer, which only is for reading the pressure of the probe. 

 

 
 
 

 
 
 

 
 

 

10.

 

ADJUSTING AND MOUNTING THE SENSORS 

 

 

The upper sensor plate determines if the probe is in top position. 

 
 

 

 
 

 

The sensor plate in the middle determines where the soil sample will be divided.. 

 

 
 

The lower sensor plate determines the depth in which the soil sample will be taken. 

 

 

 

 

   

 

 

The gap between both sensors and the sensor plates must be 2-3 mm. Make sure that the gap of both  
sensors towards the sensor plates is exactly the same. It is recommended to adjust the sensors in relation  

to the lower sensor plate. 

 
 

 
 
 

 
 

 
 
 

Summary of Contents for 2000


















Reviews:

No comments

Related manuals for 2000

Roland SP-404MK2 Reference Manual preview
SP-404MK2
Brand: Roland Pages: 136

Brands by name

Popular brands

Load more brands