background image

22

AUTOMATIC OPERATION

23

AUTOMATIC TWILIGHT  OPERATION

Automatic time mode

Using the automatic time mode you can lower and 
raise the roller shutter automatically at your adjus-
ted operating times.

1. 

Operating time to raise the shutter:

Press the Time- and Up-button simultaneously at 
your desired time. Thus, this switching command is 
saved and will be repeated every 24 hours. 
The Clock-LED shines.

Change the operating times:

You can modify the already set operating times by 
pressing the Time- and Up-/Down-button simulta-
neously at the new desired time (see no. 1 + 2). This 
way you delete the old switching times and overri-
de/ replace them with the new ones. 

2. 

Operating time to lower the shutter:

Press the Time- and Down-button simultaneously at 
your desired time. Thus, this switching command is 
saved and will be repeated every 24 hours. 
The Clock-LED shines.

1. 

You deactivate this automatic system by pres-

sing the Moon-button for about 2 seconds – the 

Moon-LED will turn off . When you repeat this pro-

cedure, you activate the automatic system again.

2. 

Set a limiting value for the automatic twi-

light operation:

Press the Moon- and Time-button short and simul-
taneously. 

3. 

Activate/ deactivate the operating times:

Press the Up- and Down-button short and simul-
taneously. This way you deactivate the operating 

times. The Clock-LED turns off . To reactivate them, 

repeat the procedure. The Clock-LED shines again. 

Automatic twilight operation

 

This automatic operation causes the 

roller shutter to close at dusk automatically till the 
lower end position (it only functions with a connec-
ted/registered light sensor).
The shutter will reopen at the programmed opening 
time or after a manual Up-command is given.

The currently measured light intensity value will 

be stored and confi rmed by a short fl ashing of the 

Moon-LED.
If you use the automatic twilight operation, the 
automatic closing time of the automatic time mode 
is (permanently) deactivated.

D

d ä m m e r u n g   e i n   a u t o m a t i s c h e s

Schließen des Rollladens bis zum un

Dämmerungsautomatik

Deaktivieren

Grenzwert der Dämmerungs-

Summary of Contents for eWickler Comfort eW910



















Reviews: