26
FACTORY DEFAULT SETTINGS – MAINTENANCE – RESET
27
DEVICE FAILURE
Maintenance
Check your eWickler and all components of your roller shutter system
regularly for signs of damage:
•
The return pulley/ defl ection roller on the roller shutter box must
move easily and smoothly.
•
The belt should not unravel at its sides or show any other kinds of
damages.
•
Please let damaged parts be immediately exchanged by your roller
shutter specialist or specialized dealer.
Restore factory default settings:
Software reset:
Press the Up-, Down- and Time-button
simultaneously until all LEDs shine.
Now the eWickler is reset to its initial
delivery state.
At the belt winders with radio all re-
gistered wireless devices and remote
controls will be deleted.
Hardware reset (reboot):
Shortly pressing the Reset-button cau-
ses a reboot of the device.
The operating times (opening and clo-
sing time) have to be set anew while
all the other settings are kept/main-
tained.
Care of equipment
You can clean the eWickler using a damp cloth. Please do not use
aggressive or abrasive cleaning agents.
Geräteausfall – Gurtband entfernen
enn der eWickler einmal ausfallen sollte
und der Motor nicht mehr läuft, können Sie
r Getriebeentriegelung das Gurt-
band vollständig aus dem Gerät entfernen,
ohne es zerstören zu müssen.
Hierzu gehen Sie wie folgt vor:
Ziehen Sie den Netzstecker
Bauen Sie den eWickler aus.
Mit Hilfe der beiliegenden Entriegelungs-
klammer können Sie nun das Getriebe
Achtung: Halten Sie das Gurtband fest,
da ansonsten der Rollladen ungebremst
herunterfallen kann.
Beim Drücken der Entriegelungsklammer ist
ein kleiner Widerstand zu überwinden.
Dazu halten Sie die Entriegelungsklammer
gedrückt und ziehen das Gurtband weitmög
lichst aus dem eWickler heraus.
Lösen Sie danach das Gurtband vom Befes
tigungshaken und ziehen es vollständig aus
dem eWicker
Positionieren Sie anschließend die Entriege
lungsklammer wieder in Ihrer Parkposition.
Device failure – removing the belt
If the eWickler should fail once and the motor
does not run anymore, you can pull the belt, with
the help of the gears’ release function, out of the
device completely without having to destroy it.
In that case, follow these steps:
•
Pull the plug.
•
With the help of the enclosed disengaging
bracket (at the inside of the belt cover) you
can now unlock the gears.
At pushing the disengaging bracket into the cor-
responding opening at the side of the device, you
have to overcome a slight resistance.
Hold the disengaging bracket fi rmly in place and
pull the belt out of the eWickler as far as possible.
Then remove the belt from the fi xing hook and pull
it out of the eWickler entirely.
Afterwards, place the disengaging bracket back in
its storage holder.
Careful! Hold the belt tightly because
otherwise the roller shutter can fall
down unbraked.
Factory default settings electronic swivel belt winder Standard
Fire function:
Active (only eW9xx-F)
Automatic sunlight operation:
Installed, activated by connecting a sensor
eSO371 (eW910/ eW910-F/ eW930-F) or
eSO400 (only eW930-F)
Automatic twilight operation:
Installed, activated by connecting a sensor
eSO371 (eW910/ eW910-F/ eW930-F) or
eSO400 (only eW930-F)
Beim Drücken der Entriegelungsklammer ist
ein kleiner Widerstand zu überwinden.
Dazu halten Sie die Entriegelungsklammer
hen das Gurtband weit-
möglichst aus dem Schwenkwickler heraus.
Lösen Sie danach das Gurtband vom Befes-
tigungshaken und ziehen es vollständig aus
Parkposition, auf der Innenseite der
Wickelradabdeckung.
Summary of Contents for eWickler Comfort eW910
Page 17: ...32 NOTES NOTES 33 ...