Sensor einstellen
Dämmerungsautomatik:
[Mond]-Taste 2s drücken:
aktiviert / deaktiviert die
Dämmerungsfunktion. Die Mond-LED leuchtet / leuchtet nicht
Grenzwert Dämmerungsautomatik einstellen:
[Mond]-Taste und [Uhr]-Taste kurz gleichzeitig drücken. Der
aktuell gemessene Wert wird gespeichert und durch kurzes
aufblinken der Mond-LED bestätigt.
Sonnenautomatik:
[Sonnen]-Taste 2s drücken: aktiviert / deaktiviert die Sonnen-
funktion. Die Sonnen-LED leuchtet / leuchtet nicht
Grenzwert Sonnenautomatik einstellen:
[Sonnen]-Taste und [Uhr]-Taste kurz gleichzeitig drücken. Der
aktuell gemessene Wert wird gespeichert und durch kurzes
aufblinken der Sonnen-LED bestätigt.
Die zuvor beschriebenen Funktionen sind nur mit dem Zubehör eSO371
(eW910/eW910-F/eW930-F) oder eSO400 (nur eW930-F) aktivierbar!
Schaltzeiten einstellen/verändern/aktivieren:
Schaltzeit Heben - einstellen/verändern:
[Uhr]-Taste und [Auf]-Taste zur gewünschten Zeit gleichzeitig
drücken. Damit wird der Schaltbefehl gespeichert und alle
24h wiederholt.
Die Uhr-LED leuchtet.
Schaltzeit Senken - einstellen/verändern:
[Uhr]-Taste und [Ab]-Taste zur gewünschten Zeit gleichzeitig
drücken. Damit wird der Schaltbefehl gespeichert und alle
24h wiederholt.
Die Uhr-LED leuchtet.
Schaltzeiten aktivieren/deaktivieren
[Auf] und [Ab]-Tasten gleichzeitig drücken, die Schaltzeiten
sind nun deaktiviert. Die Uhr-LED erlischt. Zum aktivieren wie-
derholen Sie den Vorgang.
Die Uhr-LED leuchtet / leuchtet nicht.
14
Grundeinstellungen: Endpunkte einstellen
Ohne Endpunkteinstellung läuft der Schwenkwickler nur solange,
wie eine der beiden Bedientasten gedrückt wird.
Den oberen Endpunkt einstellen
[Auf]-Taste und [Endpunkt]-Taste drücken und gedrückt halten.
Der Rollladen fährt hoch, an dem gewünschten, oberen Endpunkt
eine der Tasten loslassen
.
Der obere Endpunkt ist eingestellt.
Den unteren Endpunkt einstellen
Wiederholen der zuvor beschriebenen Punkte mit der
[Endpunkt]-Taste + [Ab]-Taste
[Uhr]-Taste
[Mond]-Taste
[Endpunkt]-Taste
[Auf]-Taste
[Sonnen]-Taste
[Ab]-Taste
[Reset]-
Taste
LED Anzeigen
14
QUICK START GUIDE
QUICK START GUIDE
15
Time-button
Up-button
Sun-button
Down-button
Reset-button
Moon-button
LED indicators
end positionbutton
Set/ change/ activate the operating times
Set/ change the opening time
Automatic twilight
operation:
Press the Time- and Up-button simultaneously at the desired
time. Thus the switching command is saved and will be repea-
ted every 24 hours.
The Clock-LED shines.
The Moon-LED shines/ does not shine.
The Clock-LED shines.
Adjust the sensor
Press the Moon-button for 2 seconds:
this will activate or deactivate the automatic twilight function
Press the Moon- and Time-button shortly at the same time. The
currently measured value will be stored and confi rmed by a short
blink of the Moon-LED.
Press the Sun-button for 2 seconds: this will activate or deactivate
the automatic sunlight function.
The Sun-LED shines/ does not shine.
Press the Sun- and Time-button shortly at the same time. The cur-
rently measured value will be stored and confi rmed by a short blink
of the Sun-LED.
The functions described before can only be activated with the acces-
sories eSO371 (eW910/eW910-F/eW930-F) or eSO400 (only eW930-F)!
Basic settings: set the end positions
Without confi guring the end positions the eWickler will only move
as long as you press one of the two control buttons.
Set the upper end position
Press the Up- and End position-button and hold them. The roller
shutter moves upwards.
At the spot you desire,
release one of the buttons
. Thus, the
upper end position is adjusted.
Set the lower end position
Repeat the previously described steps using the End position- and
Down-button.
Set/ change the closing time
Set a limiting value for the automatic twilight operation:
Automatic sunlight operation:
Set a limiting value for the automatic sunlight operation:
Activate/ deactivate the operating times
Press the Time- and Down-button simultaneously at the desired
time. Thus the switching command is saved and will be repea-
ted every 24 hours.
Press the Up- and Down-button simultaneously. The switching
times are now deactivated. The clock LED turns off . To activate
the operating times again, repeat the process.
Summary of Contents for eWickler Comfort eW910
Page 17: ...32 NOTES NOTES 33 ...