background image

 

Manuel d'information à l'utilisateur final 

L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur 

final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de 

l'utilisateur du produit final qui intègre ce module. 

Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires 

requises et avertissements comme indiqu

é

  dans ce manuel.

 

Caution :

 

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to 

reduce the potential for harmful interference to co-channel mobile satellite systems; 

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz 

and 5470-5725 MHz shall comply with the e.i.r.p. limit; and 

(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz 

shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point 

operation as appropriate. 

(iv) Users should also be advised that high-power radars are allocated as primary 

users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that 

these radars could cause interference and/or damage to LE-LAN devices. 

Avertissement: 

Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions 

précises sur les restrictions susmentionnées, notamment : 

(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés 

uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage 

préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; 

(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 

350 MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.; 

(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 

825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à 

point et non point à point, selon le cas. 

Summary of Contents for DNUR-S2

















Reviews: