background image

Sensoric

Sensoric GmbH Berlin ©     www.witt-sensoric.de

3

Sensoric

Key to symbols

Safety instructions

Recommendation for optimal procedure.

Risk of death in the case of non-observance.

•  The safety instructions in the operating manual must be observed.

•  Installation and electrical connection may only be carried out by trained personnel.

•  The safety light curtain complies with the requirements of Category 2 and PL=d 

as per EN 13849-1 and must be integrated into the operating procedure in a fault-

free manner in accordance with the applicable regulations and standards in order 

to achieve proper protective functioning.

•  In accordance with EN 12978, the safety light curtain is suitable for all door types 

apart from sluice and dock gates, lift doors, vehicle doors, gates used mainly in an-

imal husbandry, textile theatre curtains, railway level-crossing barriers, barriers that 

are used solely for vehicle traffic, and dangerous machines that are not doors.

•  During mounting, installation and commissioning, it must be ensured that the pho-

to switch system cannot be influenced by other photo switch systems or sources of 

infrared light.

•  The applicable standards and regulations – particularly EN 12453 (Safety in use of 

power operated doors) – are to be observed during mounting, installation, commis-

sioning, maintenance and repair.

•  Strictly observe the regulations of the EN12978 when connecting safety devices 

on power operated doors. 

•  The manufacturer assumes no liability for damage caused by operation and con-

nection errors, non-observance of the operating manual or lack of maintenance or 

care; the manufacturer wishes to draw attention again to the possible hazardous 

situations that can arise in this way.

•  Notwithstanding conformity with harmonised standards, it is not possible to 

foresee every potential risk. For this reason, persons should only be present in the 

hazardous area when necessary.

Summary of Contents for LIGI-10 FLEX Series

























Reviews: