30
www
.wittur
.com
Changes can be made without notice
PM.2.004923.EN - 811-000-000 SDS
©
DC-PWM Compatible · Edition 22 July 2020
Drive - Instruction Manual
9 MAINTENANCE MENU - DIAGNOSTICS AND ALARM MANAGEMENT
9.1 CONSULTING THE MAINTENANCE MENU WITH THE HANDSET
•
Connect the handset to the RJ45 connector
•
If necessary, using keys
ã
and
ä
choose the required language and confirm with the “OK” key or confirm the suggested language
with “OK”
•
Using keys Up Arrow” and
ä
, run through the “main menu “and choose “Maintenance”
•
Press “OK” to confirm the choice
•
The following options are viewed on the display:
−
MONITOR
−
STATISTICS
−
LAST ALARMS
−
ALARMS COUNTERS
−
DISPLAY CONTRAST
−
BATTERY
−
MLC MONITOR (MAIN LIFT CONTROLLER MONITOR)
−
WARRANTY DATA
•
The following options are available:
−
“BACK”: Press key F1 to restore the MENU MAINTENANCE
−
“MENU”: Press key F3 to restore the MAIN MENU
•
Using keys
ã
and
ä
, run through the MAINTENACE menu and choose the required option
•
Press “OK” to confirm the choice
If the option
MONITOR
is chosen, the display shows opening and closing speed profiles, with a indication of the speed in m/s. The
following options are available:
•
“Loop”: Pressing key F1 the door performs a number of consecutive opening and closing cycles until key F1 is pressed again. Before
movement it is possible to set the pause gap between an opening and closing cycle. Confirm with “OK” key.
•
“<>” or “ >< “: Press key F2 to let the doors respectively open or close
•
“MENU”: Press key F3 to restore the MAIN MENU
If the option
STATISTICS
is chosen , the display shows the door total working time expressed in days:hours:minutes, the cycle total
number which have been performed in this working time and the manufacture date. The following options are available:
•
“BACK”: Press key F1 to restore the menu MAINTENANCE
•
“MENU”: Press key F3 to restore the MAIN MENU
If the option
LAST ALARMS
is chosen the display shows the last occurred alarms showing their code, the relevant description and time
of occurrence (day :hour :minute from the door controller start-up). Using keys
ã
and
ä
, run through the stored alarm list. The following
options are available:
•
“BACK”: Press key F1 to restore the menu MAINTENANCE
•
“CANC”: Press key F2 to cancel all stored alarms
•
“MENU”: Press key F3 to restore the MAIN MENU
If the option
ALARMS COUNTERS
the display views the alarm list showing their code, the relevant description and the number of times
they have occurred. Using keys
ã
and
ä
, run through the stored alarm list. The following options are available:
•
“BACK”: Press key F1 to restore the menu MAINTENANCE
•
“CANC”: Press key F2 to cancel all stored alarms
•
“MENU”: Press key F3 to restore the MAIN MENU
The viewed alarms are the same as in the Alarms Table in
If the option
DISPLAY CONTRAST
is chosen, the display shows a dark square and allows the setting of the LCD contrast, by means of the
ã
and
ä
keys; adjust to best view and confirm with “OK” key. The following options are available:
•
“BACK”: Press key F1 to restore the menu Maintenance
•
“MENU”: Press key F3 to restore the Main Menu
If the option
BATTERY
is chosen, the display shows either battery voltage (in Volt) and status (in charge or in use) or just “not present”.
The following options are available:
•
“BACK”: Press key F1 to restore the menu Maintenance
•
“MENU”: Press key F3 to restore the Main Menu
If the option
MAIN LIFT CONTROLLER MONITOR
is chosen, the system IS BACK TO FOLLOW MAIN LIFT CONTROLLER’S SIGNALS; the
display shows a complete list of the input/output signals with their value.
When the input or output signal is activated the character on the display will change their graphic in white with dark background.
The following options are available:
•
“BACK”: Press key F1 to restore the menu MAINTENANCE
•
“MENU”: Press key F3 to restore the MAIN MENU
If the option
WARRANTY DATA
is chosen, the display shows:
•
warranty expiration date
•
the activity hours left before warranty expiration
•
the software version in use
•
the motor code in use
The following options are available:
•
“BACK”: Press key F1 to restore the menu MAINTENANCE
•
“MENU”: Press key F3 to restore the MAIN MENU
