background image

Gearless Lift Machine

WSG/WGG-29
Operating Instructions

Code

GM.8.002662.EN

Date

04.02.2019

Version

0.19

Page

19

Subject to changes without notice !                                                                                                                                                                                                     Subject to changes without notice !

EN

6.4. Filter mats  

Remove the three screws from the protective screen.  Then remove the screen and filter to clean or replace the
filter mats. 

Warning

Do this work only with the fan switched off as the rotating fan wheel could be dangerous.

Operation of the motor without filter mats is not permitted!

DE extraction of the grease 

NDE extraction of the grease 

Extraction of the grease

With the re-lubrication the old or surplus grease is pressed in a collector duct. The collector duct is big enough
to catch grease of 12…15 proper re-lubrications and is therefore sufficient for the lifetime of the machine.

If necessary, the collector duct can be opened with a grub screw on D-end and ND-end.

Grub screw

DIN 916-M 20 x 25

Grub screw

DIN 916-M 10 x 12

Summary of Contents for WGG-29.1




























































Reviews: