Wizard 8500e Getting Started Manual Download

Page: 3 / 38

\Manuals\GettingStartedManual8500eRev2

10/02/08

MatDesigner

™

- Getting Started Manual - Model 8500e

MatDesigner

™

8500e - Getting Started

Manual

Contents

Packing List ................................................................................................7

Check Contents .........................................................................................................7

Equipment Required .................................................................................................7

Setting up the 8500e Board .......................................................................8

Setting up the Stand or Wall Mount ..........................................................8

Assembling the Wall Mount ................................................................................8

Assembling the Stand .........................................................................................8

Taking the Board out of the Box ...............................................................8

Black Protective Covering Sheet .....................................................................10

Unlocking the Shipping Blocks .............................................................................10

Unlock the Gantry Wheels...................................................................................... 11

Check Squareness ..................................................................................................1

Check the Alignment Arrows ............................................................................1

Check the Toothed Belt Lines ..........................................................................1

Head Installation .......................................................................................1

Install the Head onto the Gantry ............................................................................1

Expose the Blade ....................................................................................................15

Installing the ST 500 Straight Line Trimmer...........................................16

Slide on the Straight Line Trimmer ........................................................................16

Hooking up the Gantry and ST 500 Air Lines ........................................17

Connecting the Board Cable ..................................................................................17

Calibration and Alignment of the Straight Line Trimmer ......................19

Using the Straight Line Trimmer ............................................................................19

Calibration and Alignment of the Straight Line Trimmer ....................................19

Install Hoods .............................................................................................1

Hook up Computer ...................................................................................1

Hook up Computer Peripherals .............................................................................1

Connect the ECU .....................................................................................................

Summary of Contents for 8500e







































Search results

Summary of Contents for 8500e

Reviews:

Related manuals for 8500e

Brands by name

Popular brands

Wizard 8500e, Getting Started Manual

Search results

Summary of Contents for 8500e

Reviews:

Related manuals for 8500e

Brands by name

Popular brands