background image

1.        Stick mode 1/3 indicator
2.        Throttle trim tips
3.        Yaw trim tips
4.        Percentage of the reaction
5.        Transmitter battery indicator 
6.        Stick mode 2/4 indicator
7.        Forwards and backwards trim tips
8.        Crab trim tips

Insert the battery by sliding the cover down. Then insert 6 x AA 
batteries as indicated under the cover.

Headless Mode Operation : Straighten the copter (red blades are in front) , long press Headless Mode button 2 seconds to enter 
into Headless Mode, the transmitter will start beeping; Long press Headless Mode button 2 seconds to exit, the transmitter will 
stop beeping.

 - Using the throttle you can control the rotation axis of the drone. Using the directional joystick you can control the flight direction 
of the drone.
 - The mode available on this model is the mode 2 with the layout of the throttle on left. It is not possible to switch mode on this 
model.
 - The different calibration buttons help keep the drone stationary. Test this by pressing the accelerator and calibration buttons to 
maintain the drone in one place.
 - You can choose the percentage of the speed. The higher the value, the faster the reaction will be (e.g. 100% will be more 
responsive than 40%).
 - The two module buttons are used to activate different modules : photos / shots / basket.

Altitude hold

Starting the copter:

- Turn on the remote

- Arm the quad by moving trottle to left bottom and direction to right bottom

- Trottle up and it will fly to approx 1m altitude and maintain hight

This model is equipped with a barometer. The barometer allows the quadcopter to hold altitude without using the remote.

- Alternatively throttle down and when it is securily landed disarm the quad by moving trottle to left bottom and direction to right 

- Adjust altitude with throttle up/down

Ending:

- Connect the battery to the copter.

- By holding it down for more than 2 sec. you use the throttle to make height. By holding it down for just one seconde, the copter 

- Trottle up/down to connect drone to remote

- Keep light button (middle right) pressed for 1sec and it will autoland

Copyright WLtoys.eu | DroneX BV

Summary of Contents for Q222











Reviews: