23
-
如果感到跑步带很干燥,那么你必须用随机附赠的润滑油来润滑。
Lubrication procedure:
润滑程序:
-
Stop the belt, so that the belt seam is on top.
-
停止跑步带,使跑步带的接缝露在表面。
-
Turn of the main switch.
-
切断主开关
-
Lift the belt from the running boars and bring some of the oil equally dispensed on the running board.
-
将跑步带由跑步板上举高,将一些油均匀地涂在跑步板表面。
-
Repeat the same on the other side of the belt.
-
在跑步带的另外一面重复同样的动作。
-
Start the treadmill with a speed of about 1 km/h and walk left and right so the belt can absorb the oil.
启动跑步机到速度为
1 km/h
,左右走动以让跑步带吸收油脂。
During designing of the treadmill, safety had the highest priority. If an electronic malfunction occurs the treadmill
stops automatically. In this case torn off the main switch and turn it on again. This normally resets the electronic
and the treadmill is again ready for operation. In case not, call a specialist or the service center.
我们的跑步机设计为客户保障很高的安全系数。电子件一旦出现故障,跑步机就会自动停机。发生这种情况,请关
闭电源开关,而后。再重新打开它。如此一来,便可复原电子件,跑步机再次启动,准备开始运作。如此调整过
后,如果还是不能解决故障,请与专业人员或服务中心联系。
Never open the motor cover or the computer! This can lead to serious injuries or
damage the item.
不要打开电子表及马达护罩。这会导致重大的人身伤害或严重损害器材
Common problems and solutions
时常发生的故障
(
常见问题及处理方法
)
,
时常发生的问题
:
Malfunction
故障现象
Possible reason
可能
原因
Solution
排除措施
Switch on, computer
has no signal
接通电
源,仪表无显示
1.Power supply plug un-insert
电源插头
没插好
2.Computer poor contact with control
panel
电子表与控制板连线接触不良
3.Overloading and self-protection
过载
保护中
1.Re-insert the plug, check the socket
重新插入,并检查插座
2.Re-connect
重新连线
3.Press the overloading protect switch in
place.
按压过载保护开关到位
Display “E53”
显 示
E53
光感没反馈
Light sensation no feedback
Replace DC motor optical sensors
更换直
流电机光电感应器
Display “E50”
显 示
E50
Drive board break between up and
down.
上下控通讯不通
1.Replace the datacom chip of electric
window.
更换电子表通讯芯片
2. Replace the datacom chip of drive.
更换驱动器通讯芯片
Display E54
显 示
E54
1.Electronic inner wire abnormal.
驱动板
损坏
1.Replace the drive board
更换驱动板
Pulse rate display
abnormally
心率显示
不正确
1. Testing method is not correct
测试方法不对
2. Pulse sensor abnormal
心率传感器不良
1. Test in accordance with the correct
technique
依正确方法测试
2. Palm of the hands are too dry, keep a
certain of humidity
手心太干燥,保持一定
的湿度
3.Check the connector whether loose or
not
检查接线是否松动
4.Check the console whether abnormal or
not
检查电子表异常
9. Troubleshooting
故障排除