background image

Service Information

18

Troubleshooting

IMPORTANT NOTE:

If the pro ventilation hood does not

operate properly, follow these troubleshooting steps:

Verify that electrical power is being supplied to the

ventilation hood.

Check electrical connections to ensure that the

installation has been completed correctly.

Refer to the troubleshooting guide in the Wolf pro

ventilation hoods use & care guide.

If the ventilation hood still does not operate properly,

contact a Wolf authorized service center. Do not

attempt to repair the ventilation hood yourself. Wolf is

not responsible for service required to correct a faulty

installation.

Service Information

If service is necessary, maintain the quality built into your

ventilation hood by calling a Wolf authorized service

center.

To obtain the name and number of a Wolf authorized

service center, check the contact & support section of our

website, wolfappliance.com or call Wolf customer service

at 800-332-9513.

When calling for service, you will need the model and

serial numbers of the ventilation hood. This information is

found on the product rating plate, located inside the left

wall of the hood shell. Refer to the illustration below.

Location of rating plate
(inside hood).

RATING PLATE

Before servicing or cleaning, switch power off at the

service panel and lock the service disconnecting means

to prevent power from being switched on accidentally.

If it cannot be locked, securely fasten a prominent

warning tag, to the service panel.

Summary of Contents for Pro Island





















Reviews: