background image

Introduction

Warranty

1

1-6

doc091219

Introduction

Several components which are used in the manufacture of the equipment but not manufactured by Warrantor,
such as cant hooks, power plants, laser sights, batteries, tires, and trailer axles have warranties provided by
the original equipment manufacturer (written copies available upon request). Warrantor does not separately
warrant such items. Components or equipment manufactured by third parties are not covered by this war-
ranty. Warrantor, however, will provide reasonable assistance to the Purchaser to make claims against any
warranties applicable to such component parts as provided by such original equipment manufacturers. Com-
ponents or equipment manufactured by third parties are not covered by this Warranty. 

FIVE YEAR LIMITED CHASSIS WARRANTY 

The limited five year chassis warranty, described above, DOES NOT extend to (a) any damage stemming
from accident, improper towing, overload, abuse, misuse, abnormal conditions, negligence, excessive opera-
tion, or lack of maintenance, (b) rust caused by exposure to corrosive atmospheric conditions, or (c) the saw-
mill head, carriage, axle, brakes, or any hydraulic or electrical components attached to the chassis.

WARRANTOR’S OBLIGATIONS AS TO DEFECTS

In the event that the equipment fails to perform due to defective materials or workmanship attributable to War-
rantor under normal use and service within the established warranty period, Purchaser’s sole and exclusive
remedy and Warrantor’s sole liability shall be to replace or repair, in Warrantor’s sole and subjective discre-
tion, any defective part at Warrantor’s principal place of business without cost to the Purchaser if such defect
exists. The determination of whether a product is defective shall be made by Warrantor in Warrantor’s sole
and subjective discretion. The Purchaser must notify Warrantor prior to shipping any defective part. Warran-
tor, at its sole discretion, may cover expenses incurred in shipping the defective part to Warrantor for evalua-
tion;  provided,  however,  that  Warrantor  will  not  be  responsible  for  labor,  travel  time,  mileage,  removal,
installation, and/or incidental or consequential damages. However, any part in excess of 140 pounds must be
returned by the Purchaser to the Warrantor’s nearest authorized facility at the Purchaser’s expense, if return
is requested by Warrantor. Warrantor shall have a reasonable time within which to repair or replace the defec-
tive part. If Warrantor determines that the product is not defective under the terms of this warranty in Warran-
tor’s  sole  and  subjective  discretion,  then  Purchaser  shall  be  responsible  for  any  expenses  incurred  by
Warrantor in returning the equipment to the Purchaser. 

LIMITATIONS AND DISCLAIMERS OF OTHER WARRANTIES

EXCEPT  FOR  THE  EXPRESS  WARRANTY  PROVISIONS  STATED  ABOVE,  WARRANTOR  DISCLAIMS
ALL  WARRANTIES,  EXPRESS  AND/OR  IMPLIED,  INCLUDING  AND  WITHOUT  LIMITATION,  THE
IMPLIED WARRANTIES OF MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, NONIN-
FRINGEMENT  AND TITLE.  No  representation or other affirmation of  fact  by representatives  of Warrantor,
whether verbal or in writing, including photographs, brochures, samples, models, or other sales aids, shall
constitute a warranty, or any other basis, for any legal action against Warrantor. There are no other represen-
tations, promises, agreements, covenants, warranties, guarantees, stipulations or conditions, expressed or
implied,  by  Warrantor,  except  as  expressly  set  forth  herein.  THE  ORIGINAL  PURCHASER  AND  ANY
INTENDED USER OR BENEFICIARY OF THIS EQUIPMENT, SHALL NOT BE ENTITLED TO RECOVER
ANY  INDIRECT,  SPECIAL,  PUNITIVE,  EXEMPLARY,  CONSEQUENTIAL,  SPECIAL,  OR  INCIDENTIAL
DAMAGES OR LOSES, INCLUDING BUT NOT LIMITED TO, DAMAGES OF LOST PRODUCTION, LOST
REVENUE, LOST PRODUCT, LOST PROFITS, LOST BUSINESS, LOSS OF USE, LOSS OF GOODWILL,
OR BUSINESS INTERRUPTION, FROM WARRANTOR FOR ANY REASON WHATSOEVER INCLUDING,
WITHOUT  LIMITATION,  WARRANTY  OR  DEFECT  IN  THE  PRODUCT  REGARDLESS  OF  THE  SOLE,
JOINT,  AND/OR  CONCURRENT  NEGLIGENCE,  BREACH  OF  CONTRACT,  BREACH  OF  WARRANTY,
STRICT LIABILITY IN TORT OR STATUTORY CLAIMS, OR OTHER LEGAL FAULT, OR RESPONSIBILITY
OF EITHER WARRANTOR OR PURCHASER OR ITS EMPLOYEES OR AGENTS. Warrantor does not war-
rant that its equipment meets or complies with the requirements of any particular safety code or governmental
requirements.

Defective items, replaced under the terms of this warranty, become the property of Warrantor.

Summary of Contents for FS300




























































Reviews: