background image

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

www.woodbridgebath.com

BEFORE YOU BEGIN 

PRODUCT REQUIREMENTS 

A. Summary Of Key Requirements 

 Observe all local plumbing codes, Install the unit to a level sub

fl

oor,Provide properly

 -dimensioned framing.    

B. Product Inspection 

Uncrate and inspect bath for damage. Leave all materials in the crate during construc on to 

prevent damage.

ROUGHING-IN 

 

 

2

•  All informa on is based on the latest product informa on available at the  me of 

publica on. WOODBRIDGE

® 

 reserves the right to make changes in product 

characteris cs, packaging, or availability at any  me without no ce. 

 •  Please read these instruc ons carefully to familiarize yourself with the required 
     tools, materials, and installa on sequences. Follow the sec ons that pertain to your 

     par cular installa on. This will help you avoid costly mistakes. In addi on to proper 
     installa on, read all opera ng and safety instruc ons. 

IMPORTANT     INFORMATION 

• Measurements are ± 1/2" and subject to change without no ce 
• Speci

fi

ca ons & Con

fi

gura ons are subject to change without no ce

• Please measure tub on-site before installa on

 • Please note that installer(s) must be cer

fi

ed or warranty will be voided.

 • Measurements herein supersede all others published prior to purblica on
   date shown below
 • Before ordering or installing, please consider future access to equipment

B 0 0 9 1 / B T S 0 0 9 1

Control box

15"

Water depth

47 1/4"

35 3/8"

45 5/8"

70 7/8"

23 5/8"

27 1/2"

Air  Blower
  (0.3KW) 

B 0 0 9 2 / B T S 0 0 9 2

26 3/4"

23 5/8"

31 1/2"

20"

41 3/4"

67"

15"

Water depth

Control box

47 1/4"

37 3/4"

45 5/8"

70 7/8"

26 3/8"

23 5/8"

14 7/8"

Water depth

 Heater 
(1.5KW)

Hydromassage 
Pump (1.1KW) 

Air  Blower
  (0.3KW) 

Control box

6 5/8"

B 0 0 9 0 / B T S 0 0 9 0

Hydromassage 
Pump (1.1KW) 

Heater 
(1.5KW)

Air  Blower
  (0.3KW) 

Hydromassage 
Pump (0.75KW) 

Heater 
(1.5KW)

Summary of Contents for B0090
















Reviews: