background image

Z4:  Middle guardrail beam near the ladder.

W13, W15, W16  middle round indentations are used only
when the ladder is placed at the head or foot of the bed.

W17: has extra A hole to attach a ships wheel.
     

W14, W19, W20, W21, W22 

W23: has a large round indentation for wall 
attachment.

Z11: Can be assembled mirror image when the ladder is 
placed on the other side.

A

S1,
S5

S6,
S8

S7

S2

S3

Z31

S4

Z30

W9, W10: Notch for the mattress support beam should always face up!

W2, W3:  Pre-drilled hole “L” indentations are for ladder attachment (leave them free until the end of assembly).

W7:Only two out of four “L” holes are used depending on which side the ladder is attached!

W1, W8, W11, W12: Warning! 2 “L” holes underneath and 3 “L” holes facing the inner side.

W18:  Beam to hold the climbing rope (set up of this middle beam is optional).

L

L

L

L

L

L

L

L

Middle Beam

Ladder Beam

Corner Beam

Holes for ladder handles

When setting up the long

vertical beams, only use the

upper drilled holes since 

the lower ones are used

for other assembly options

inner side

inner side

inner side

inner side

Notch beam

for mattress support beam

inner side

Warning! The upper three 

circular indentations (    ) of    

corner beams S6, S8, S1

 and S5 should face

the top-middle beam

 (W18) during the set up

Hole for

wall

attachment

 bed inner side

Not all specifications are guaranteed.

© Copyrights by WOODLAND 1998

Corner Beam

The stickers on the beams
(“W1”, “W2”...etc.) Can be 
found on the end of every 
beam. “W” for horizontal, 
 “S” for vertical!

Horizontal beams are shown
horizontally and vertical beams 
are shown vertically.

Familiarise yourself with the
location of the beams and
their 20mm circular indentations:
The inner side of the beams are
displayed as this is where most
of the circular indentations are 
located.

Beam List

AMARILLO

Pos.No. 504

Assembly Assistance

WARNING!

Danger of small children 

swallowing the covering of 

round indentatons.

TIP:
Should a frame set or arm and back rest 
set be assembled with the WOODLAND 
bed please make sure to read the other 
instructions 

before

 the assembly of the 

bed!

inner side

inner side

inner side

inner side

R

Summary of Contents for AMARILLO 504

Page 1: ...em Please use the beam list as an additional help Also there is a label on the boxes to indicate the content of the box Before you start Safety rail Z25 Safety rail Z26 Safety rail Z26 Safety rail Z24 screwed from inside Safety rail Z27 Assembly Instructions for AMARILLO Pos 504 B1 B16 B17 B32 W16 W15 W17 Z11 W3 Z30 Z31 W7 S1 S8 S7 W18 W13 W2 W14 W1 P1 S6 S5 S2 Beams S1 S5 S6 and S8 with round ind...

Page 2: ... drilled holes since the lower ones are used for other assembly options inner side inner side inner side inner side Notch beam for mattress support beam inner side Warning The upper three circular indentations of corner beams S6 S8 S1 and S5 should face the top middle beam W18 during the set up Hole for wall attachment bed inner side Not all specifications are guaranteed Copyrights by WOODLAND 199...

Page 3: ...e built from top to bottom so that it makes it easier to screw nuts with screwdriver Then tightly screw the bolts at the bottom so that it makes it easier to construct the rest of the bed Ladder assembly in one end of five rung holes of beam S3 add drops of wood glue included in delivery Tap in the steps using a hammer and wooden board Do not put glue on the other side so that another step can be ...

Page 4: ...tter to attach the bed to a wall It is recommended to use the upper hole on the S7 beam for an attachment also it is possible to attach the beam W23 to a wall with the supplied anchor and the 80mm or 100mm long Hexagonhead bolt If the bed does not have direct contact with the wall it is necessary to place a piece of wood between the bed and the wall After approx three weeks tighten the bolts again...

Reviews: