background image

12 

 
 

Err 2 

Lid is not properly latched 

Open lid and close it 

properly 

Err 52 

Rotor is stuck 

Turn the centrifuge off. 

Check and fit the rotor 

properly and turn the 

centrifuge on 

Power tripping 

Cable does not fit 

properly 

Remove cable and 

connect properly 

Last run memory not 

displayed 

The centrifuge was 

turned ON immediately 

after being turned OFF 

Maintain a 3 second gap 

between turning the 

centrifuge OFF and ON 

System hang/freezes 

Electronics error 

Switch off centrifuge and 

then switch it ON again. If 

the error still shows, 

contact Woodley 

Equipment Company 

 

NOTE

:

  

1.

 

Maintain  a  3  second  gap  between  restarting  the  centrifuge.  Instantly 
switching ON-OFF can lead to a reset, erasing the last run memory.

 

2.

 

If the centrifuge is hot which may result in a fluctuation in speed then allow 
it to cool for at least 30 minutes whilst not using it. 

3.

 

Do not use liquids with density higher than 1.2g/ml for full load operation.

 

 

14.

 

 Warranty 

This product is warranted to be free from defects in material and workmanship for a 
period of two (2) years from date of purchase. Your product will be duly repaired 
upon prompt notification in compliance with the following conditions: 

This warranty is valid only if the product is used for its intended purpose and within 
the guidelines specified in this manual. This warranty does not cover damage caused 
by accidents, neglect, misuse, improper service, natural forces or other causes not 
arising from defects in original material or workmanship. This warranty does not 
cover any incidental or consequential damages, commercial loss or any other 
damages from the use of this product. 

The warranty is invalidated by any non-factory modification which will immediately 
terminate all liabilities on Woodley Equipment Company Ltd for the products or 
damages cause by its use. The buyer and its customer shall be responsible for the 
product or use of products as well as any supervision required for safety. If 
requested, the products must be returned well packed and all shipping charges must 
be paid. 

Summary of Contents for Clinispin HCT II















Reviews: