Assembly
23
MAN1260 (4/09/2018)
Chain Shielding Installation (Optional)
Full chain or rubber shielding must be installed when operating in
populated areas or other areas where thrown objects could injure people
or damage property.
•
If this machine is not equipped with full chain or rubber shielding,
operation must be stopped when anyone comes within 300 feet (92
m).
•
This shielding is designed to reduce the risk of thrown objects.
The mower deck and protective devices cannot prevent all objects
from escaping the blade enclosure in every mowing condition. It is
possible for objects to ricochet and escape, traveling as much as 300
feet (92 m).
Figure 33
. Chain Shield Installed
1.
Install chain shielding plate (3) to rear mower frame as shown.
2.
Secure with carriage bolts (14) and flanged lock nuts (15).
Insert carriage bolts from bottom upward as shown.
Front Roller Installation (Optional)
1.
Insert four carriage bolts (5) through the front mower frame from inside
out.
2.
Place roller bracket (8) over bolts; then install flange whiz nuts (6) on
bolts and tighten.
3.
Place front roller (9), two bearings (10), spacer (7) and two flat washers
(4) between roller bracket as shown in Figure 34.
4.
Insert cap screw (3) through bracket and roller.
5.
Secure with flanged lock nut (2). Do not overtighten, roller must spin
freely.
Figure 34
. Front Roller Installation
Quick Hitch Kit Installation (Optional)
NOTE:
This kit allows mower to only fit on a Category 1 standard quick hitch.
1.
Make sure that you are using one of the front two attachment points (D)
in the lower hitch plates. See Figure 6, page 10, for adjustment.
2.
Remove clevis pins from lower hitch arms. The pins will not be used for
the Quick Hitch.
3.
Attach offset link (1) to lower hitch clevis using sleeves (3 & 8), two flat
washers (9), cap screw (11), and hex nut (12) as shown in Figure 35. Do
not tighten hardware. Repeat for opposite side.
4.
Attach upper end of offset links (1) to each side of U-bracket link, using
two flat washers (5), sleeves (6 & 10), flange lock nut (7), and 1/2 x 4-3/4
cap screw.
5.
Remove rear offset links. They will be replaced with chains (2)
6.
Attach chains to top of A-frame on both sides as shown, using cap screw
(4), two flat washers (5), and nut.
7.
Attach opposite ends of chains (2) to rear mower frame as shown. Cut
chains to length (see chart above). Vary length slightly as desired. Twist
chain to make finite adjustments in length until unit lifts level.
8.
Tighten all hardware.
15
14
CM768
3. Shield, chain plate
14. Bolt, carriage 3/8 NC x 1
15. Nut, flanged lock 3/8 NC
3
2. 1/2 NC Flanged lock nut
3. 1/2 NC Flanged lock nut
4. 1/2 SAE Flat washer
5. 3/8 NC x 1 Carriage bolt
6. 3/8 NC Flanged whiz nut
7. Spacer, 19.1 x 168.3 mm (.75 x 6.62")
8. Bracket, front roller
9. Roller, 101.6 x 187.2 mm (4 x 7.37")
10. Bearing
Summary of Contents for PRD6000E
