Woodster Os 58, Translation From The Original Instruction Manual

english 13

After finishing the grinding turn off the machine and dis-
connect the main plug.

ATTENTION!! Use dust mask, protective goggles and vacuum 
extraction.

m

 Electrical connection

The installed electric motor is factory connected ready for 
operation. The connection meets the applicable VDE and 
DlN regulations.
The connection made by the customer as well as any ex-
tension cables used must comply with all relevant regula-
tions.
Connection and repair work on the elctric equipment must 
be carried out by a qualified technician only.

Important note

The motor rating is S 1. This means that when overloaded 
it  switches  off  automatically.  After  a  cooling  period  (can 
vary) you may switch it on again.

m

 Maintenance

Disconnect the main plug before conducting any maintenance 
work.

Cleaning the machine after every use is recommended. 
Keep  the  safety  devices,  air  boxes  and  the  crankcase 
clean.
Clean the machine with a cloth.
Do not use any solvents or cleaning agents because they 
could harm the plastic parts of the device.
Do not let water get into the interior of the machine.
The  interior  of  the  machine  is  completely  maintenance-
free.

EC Declaration of Conformity 

We herewith declare, 

Woodster GmbH, Günzburger Str. 69, D-89335 

Ichenhausen 

that the machine described below due to its con struc-

tion and design and in the version delivered by us complies with the 
relevant provisions of the following EC Directives. 
In case of a modification of the machine this declara tion ceases to be 
valid. 

Machine description: 

Bench Grinder

Machine type: 

os 58,

 Art.-Nr. 390 3401 000, 390 3401 901, 390 3401 902, 

390 3401 903

Relevant EC directives: 

EC machine directive 2006/42/EG, 
EC Low voltage directive 2006/95/EWG, 
EC-EMV directive 2004/108/EWG.

Applied harmonized European standards 

EN 12100-1, EN 12100-2, EN 13857, EN 60 204-1, EN 61029-1/A12,  
EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3

Notified body within the meaning of Annex VII

TÜV Süd, Product Service GmbH, 80339 München

Engaged for: 

EG-Baumusterbescheinigung M8 0702 49613 040, 
GS-Prüfung Z1A07024961309

Place, date: 

Ichenhausen, 02.09.2009

Signature:  

Thomas Honigmann (Manager)

Trouble shooting

Problem

Possible Cause

Help

Motor doesn’t start

a) ON/OFF switch damaged.
b) ON/OFF cable damaged.
c) ON/OFF relay damaged. 
d) Fuse blown.

e) Motor burnt.

a-d)  Replace all damaged parts before you use 

your machine again. 

e)  Contact your local service centre. Every 

attempt to carry out a repair, can be 
dangerous if it is not done by skilled 
personnel.

Machine gets slower 
during work.

Too much pressure put on the workpiece.

Reduce the pressure on the workpiece.

Sanding belt comes off 
the drive pulleys.

Belt does not run straight.

Reset the track.

The wood gets burnt 
during sanding.

a)  Sanding disc or belt covered with grease.
b)  Excessive pressure on workpiece.

a)  Replace disc or belt.
b)  Reduce pressure on workpiece.

Strong vibrations

a) loosely mounted tool 
b) defective tool 
c) spindle knocks

a) tighten tool
b) change tool 
c) repair at a Service-Station