background image

Model W1784 (Mfg. Since 2/07)

-3-

1.  HAND INJURIES: 

Do not place 

your hands near the staple point 
of entry. A staple can deflect and 
tear through the surface of the 
workpiece, puncturing your hand or 
fingers.

2.  COMBUSTIBLE GASES: 

Never 

connect the stapler to pressurized 
oxygen or other combustible 
gases as a power source. Only use 
filtered, lubricated, and regulated 
compressed air.

3.  SAFE HANDLING: 

Never point the 

stapler at others! Do not keep 
the trigger pulled when loading 
fasteners, carrying, or holding 
tool. Carry the stapler only by the 
handle, never by any other part. 
Do not carry the stapler by the air 
hose. Disconnect the stapler from 
the air hose when going up and 
down ladders.

4.  CLEANING: 

Never use gasoline or 

other flammable liquids to clean 
the stapler; vapors in the stapler 
will ignite by a spark and cause it 
to explode.

Additional Safety for Staplers

5.  HOSE USAGE: 

Make sure your air 

hose is designed for the tool in 
use, is in good condition, and is 
long enough to reach your work 
without stretching. However, an 
overly long air hose in the work 
area may be a tripping hazard. 

6.  OPERATING QUESTIONS: 

If you 

are not sure about the intended 
operation, stop using the stapler. 
Seek formal training.

7.  MAINTENANCE: 

Always disconnect 

air from the stapler when servicing 
or installing staples. During 
maintenance, a stapler connected 
to air may fire accidentally, 
causing serious personal injury.

8.  COMPRESSED AIR RATING: 

Do not 

connect the stapler to compressed 
air that exceeds 120 PSI.

9.  CHECK VALVE: 

Do not use a check 

valve or any other fitting that 
allows air to remain in the tool.

10.

 

MODIFICATIONS: 

DO NOT 

modify this tool or bypass safety 
mechanisms.

Never  point  this  stapler  at  yourself 
or  another  person!  Always  pay 
attention to the direction this stapler 
is pointed. Use this tool with respect 
and caution to lessen the possibility 
of  operator  or  bystander  injury. 
Ignoring  this  warning  may  result  in 
serious personal injury.

Stapler  accidents  routinely  happen 
while  moving  the  gun  to  another 
location,  such  as  up  ladders,  to 
another  room,  or  even  another  job 
site.  Always  disconnect  the  gun 
immediately  after  use  and  never 
transport the gun while connected to 
the air—even if the air compressor is 
disconnected from its power source!

Summary of Contents for SHOP FOX W1784





















Reviews: