background image

Inspection and maintenance

 

Greenstar 4000 – 6 720 891 162 (2020/09)

60

If the manometer reading is out of tolerance

, in the shaded area of the 

table values then carry out the following checks.
▶ Check that the siphon is not restricted or blocked.
▶ Check the exhaust paths for restrictions.
▶ Clean the heat exchanger with a suitable cleaning tool, refer to 

cleaning section.

▶ Re-check the fan pressure readings.

If the appliance, after completing the above checks, fails the fan 
pressure test then contact Worcester, Bosch Group for advice.

▶ Switch the appliance off after completing pressure check. 
▶ Disconnect the digital manometer and replace the test point cover.

8.4

Check working gas inlet pressure

NOTICE

Gas inlet pressure

▶ Do not continue with the other checks if the correct gas inlet pressure 

can not be achieved at maximum output.

▶ Check the gas supply working pressures in the system conform to the 

readings shown in the table shown in chapter 6.5 "Checking gas inlet 
pressure".

8.5

Flue gas analysis

NOTICE

Combustion testing

▶ Combustion testing must be carried out by a competent person. 

Testing must not be attempted unless the person carrying out the 
combustion check is equipped with a calibrated flue gas analyser 
conforming to BS 7967 and is competent in its use.

Flue gas analysis

▶ Ensure that the gas inlet pressure has been checked and is 

satisfactory.

▶ Refit the test point plugs after the test has been completed.

▶ Set the appliance to maximum and minimum output in chimney 

sweep mode (

  6.4 "Chimney sweep mode") for the flue gas 

analysis checks.

▶ Check that the readings conform to those given in the following 

tables. In addition to CO and CO/CO

2

 ratio checks also check the 

maximum and minimum CO

2

 percentage reading.

CO/CO

2

 settings 

Table 30 CO

2

 settings

If the CO

2

 is out of tolerance then please check:

▶ The gas inlet pressure.
▶ The  gas  rate.
▶ The fan test pressure.
▶ The flue and air intake, plus any possible blockages in the condensate 

disposal.

▶ The condition of burner.
▶ For leaks or obstructions in the exhaust paths.
▶ That the injector is clean.

After all checks have been completed and the CO

2

 is still out of tolerance 

then contact Worcester, Bosch Group helpline 0330 123 3366 before 
making any adjustment to the gas valve.

8.6

Checking the flue integrity

NOTICE

▶ Check flue joints are secure, the terminal and the terminal guard, if 

fitted are clear and undamaged.

▶ Combustion testing must be carried out to BS 7967 by a competent 

person. Testing must not be attempted unless the person carrying 
out the combustion check is equipped with a calibrated Combustion 
Analyser conforming to BS EN 50379 and is competent in its use.

Flue gas analysis

▶ Ensure that the gas inlet pressure has been checked and is 

satisfactory.

▶ Refit the test point plugs after the test has been completed.

▶ Refer to chapter 6.9 "Checking flue integrity" and check that the 

readings conform to those given, confirming flue system and 
combustion circuit are ok.

8.7

Cleaning the siphon and heat exchanger

8.7.1

Checking the electrodes and cleaning the heat exchanger

CAUTION

Risk of burns due to hot surfaces! 

Individual components of the appliance can become very hot even after 
being shut down for a long time.

▶ Allow the appliance to cool down before carrying out any work.
▶ If necessary, wear protective gloves.

WARNING

Material damage due to hot flue gas! - Gaskets and seals - gas related 
components

Hot flue gas can leak through defective gaskets, damage the appliance 
and endanger safe operation.

▶ Burner/electrode assembly gasket must be replaced if disturbed.
▶ Other gaskets/seals must be checked and replaced where necessary.
▶ Do not attempt the cleaning procedure unless new gaskets and seals 

are available.

▶ Ensure that the gaskets are positioned correctly.

CO

2

 Reading

CO Reading

Natural Gas appliances

Maximum rated Output

 

1)

1) Should be measured 10 minutes after firing the appliance

Between 9.0 and 9.8%

<250ppm

Minimum rated Output

 

1)

A minimum of 0.2 lower than the maximum reading 
taken and between 8.2 and 9.0%

<250ppm

LPG appliances

Maximum rated Output

 

1)

Between 10.4 and 11.0%

<250ppm

Minimum rated Output

 

1)

A minimum of 0.2 lower than the maximum reading 
taken and between 10.0 and 10.4%

<250ppm

Summary of Contents for 7 733 600 377

































































































Reviews: