ASSEMBLY (Fig. 3
，
Fig.4, Fig 6)
Unpacking
Carefully remove the tool and all loose items from the outer
carton.
Retain all packing materials until after you have inspected and
satisfactorily operated the machine.
Before setting up, repair or maintenance of the
appliance you must always turn off the operating switch and pull
out the mains plug!
1. Rotate the foldable pole and lock two part together,
referring to fig.3.
2. Insert extention pole into the main pole, meanwhile press
the lock button (14). After the pole insert for long
distance, release the lock button and let it free. Then
move the extentioon pole forward and backward
slowly. After heard a click sound, stop moving.
Rotate the locking lever (16) upside to fasten. Please
referring fig 4.
3. Mount the dust hose onto the dust port on the rear of
handle ,and mount the other port onto the vaccum
cleaner.
4. Mounting the sanding sheet onto the sanding pad.
OPERATION (Fig 7~ Fig 12)
Electronic control (Fig 7)
This machine has the characteristics as below:
▪ Lock-on switch (5)
▪ Adjustable Speed (4)
▪ LED light belt (13)
▪ ON/OFF LED switch (12)
To start the tool, just press the switch knob (11) and meanwhile
press down the locking knob 5.
To stop the tool, just press the swtich knob (11).
Adjusting the rotation speed (Fig. 8)
The speed of the machine is variable to suit different tasks. It
can be adjusted from 800 min
-1
up to 1600 min
-1
by using the
thumb wheel. Turn in the counter clockwise direction to
increase the speed and in the clockwise direction to decrease
the speed. Generally, you should use the higher speed for fast
stock removal and the lower speed for more precise control.
Light on LED working light (Fig. 9)
Before operation, turn on the LED switch to “I” position to light
on.
Switch the LE
D swtich to “0” position to turn off.
Suction power adjustment (Fig. 10)
Reduce the suction power by turning the wheel to the
left, and increase by turning it to the right.
Working on vertical wall and ceilings(Fig 11 & 12)
When working vertical wall, the spring sets free status.
While sanding ceilings, the spring should connect the
hook on the gear box head.
Working advice
▪ Begin sanding and carefully contact the work surface
as lightly as possible-just enough to keep the sanding
head flat against the surface.
▪ The joist in the sanding head allow the sanding disc to
follow the contours of the work surface.
▪ The best technique is to use overlapping sweeps and
keep the head in constant motion. Never stop too long in
any one place or there will be swirl marks. With
experience it will be very easy to create excellent results.
MAINTENANCE
Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER
use solvents to clean plastic pats. They could possibly dissolve or otherwise damage the material.
Wear safety glasses while using compressed air.
Clean the vacuum swivel connector as too much dust will keep it from turning freely..
ENVIRONMENT PROTECTION
In order to prevent the machine from damage during transport, it is delivered in a sturdy packaging. Most of the packaging
materials can be recycled. Take these materials to the appropriate recycling locations. Take your unwanted machines to your
local dealer. Here they will be disposed of in an environmentally safe way.
Li-ion batteries can be recycled. Deliver them to a disposal site for chemical waste so that they can be recycled or
disposed of in an environmentally friendly manner.
Discarded electric appliances are recyclable and should not be discarded in the domestic waste! Please actively
support us in conserving resources and protecting the environment by returning this appliance to the collection
centres (if available).
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents:
EN60745-1:2009+A11:2010;
EN60745-2-3:2011+A2:2013+A11:2014+A12:2014+A13:2015;
EN55014-1:2006/+A1
：
2009/+A2:2011; EN55014-2:2015; EN61000-3-3:2013; in accordance with the regulations 200
6/42/ЕС, 2014/30/ЕU.
NOISE/VIBRATION Measured in accordance with EN60745 the sound pressure level of this tool is <74dB(A) and the sound
power level is <85dB(A) (standard deviation: 3 dB), and the vibration is <4,34 m/s
2
.
