background image

Troubleshooting Guide —

Problem/Causes and Remedies:

Pump will not Start

Check:

•  

Correct voltage (±10%) and electrical connections

•  

Fuse or breaker

•  

Pressure switch operation and correct voltage at switch

•  

Rectifier or motor for open or grounded circuit

•  

Locked drive assembly

Pump will not Prime (No discharge with motor running)

Check:

•  

Debris in strainer

•  

Restriction (kinks) in inlet/outlet tubes

•  

Debris or swelling in inlet/outlet valves

Pump will not Shut Off (Output line closed and no leaks)

Check:

•  

Air trapped in outlet line or pump head

•  

Correct voltage to pump

•  

Debris in pump inlet/outlet valves

•  

Loose drive assembly or pump head screws

•  

Pressure switch operations/adjustments

Leaks from Pump Head or Switch

Check:

•  

Loose screws at switch or pump head

•  

Switch diaphragm ruptured or pinched

•  

Punctured diaphragm if fluid is present

Spray & Pump FAQs —

--Why does the pump not run all the time?

    This is a demand pump and only runs with flow; spray wand, by-pass, spray tips or leak in system
--Why does the pump surge while using the spray wand?

    Low flow may cause the pump to surge (or cycle).  This could happen when the spray wand is adjusted for a small or fine spray 

    pattern.  To overcome, slightly open the by-pass valve.
--My pump quit and will not restart - what should I check?  

    Check all electrical connections.  Ensure switch is in the on position.  Check in-line fuse and/or fuse in car adapter end.  Ensure 

    correct v/- 10%.   12-13 volt
--Low flow or no flow at all - what should I check? 

    Check for a clogged suction hose and/or suction strainer.  Often you will need to clean the suction strainer.  Check for proper voltage.
--Is there a fuse for the sprayer? 

    Yes, either an in-line fuse, a fuse located in the car adapter housing or both.
--What size fuse should I use as a replacement?    

    7.5  amp
--What is the range of the spray wand?     

    35 feet max
--How should I clean the tank after use?

    Tank should be cleaned with Nutrasol® or similar tank cleaning agent, and then rinsed with water.
--How do I remove / replace fuse?  

    Unscrew in-line fuse connector, or unscrew the car adapter housing.
--Can the spray tip on the wand be replaced with a different type of tip?

    Yes, however your wand comes with a #18 tip which is standard. Brass tips generally produce better spray patterns than plastic.
--Each time I turn on the pump my fuse blows.

    1) Excessive voltage  2) Improper adjustment of the pressure switch  3) Damaged wiring harness.
--What is the warranty (time duration) on pump, tank, trailer pieces, and accessories?

    2 years as stated in operation instructions.

WARNING - Ensure the wiring harness does not become pinched or damaged in any way. This may damage the pump or cause 
the wiring harness to overheat, resulting in a melt down or fire.

PRECISION SPRAY EQUIPMENT, a divison of Green Leaf, Inc.   9490 N BALDWIN ST   FONTANET, IN 47851   www.grnleafinc.com   800-654-9808

a division of Green Leaf, Inc

®

P R E C I S I O N   S P R AY   E Q U I P M E N T

PSE

®

Summary of Contents for LG25 ESS

Page 1: ...Flush with water to clear any accumulated debris These sprayers are designed to be attached to a stable surface The purpose of this manual is to assist you in assembling operating and maintaining your lawn and garden sprayer Please read it carefully as it furnishes information which will help you achieve years of dependable trouble free operation After use fill the sprayer part way with water Star...

Page 2: ...er Assembly 600155 1 7 8 Spray Wand Clip 600151 2 18 5 mm Diameter Pinch Clamp 600149 3 9 Lead Wire Assy w Switch 96 600153 1 10 10 24 3 8 Pan 600152 2 11 Rubber Grommet 600207 1 12 15 Gallon Tank 600239 1 13 Economy Wand Hose Assembly 600261 1 14 1 0 GPM Pump w Barbed Fittings 630011 1 15 10 24 x 3 4 Truss Head Screw 630014 4 16 PRECISION SPRAY EQUIPMENT a divison of Green Leaf Inc 9490 N BALDWIN...

Page 3: ...ners Stainless steel and zinc plated Pressure Flow Amp Draw PSI Bar GPM LPM Amps 0 3 0 2 1 00 3 7 1 5 10 0 7 0 85 3 1 1 9 20 1 4 0 71 2 6 2 1 30 2 1 0 61 2 3 2 4 40 2 8 0 42 1 6 2 6 Parts List Ref Part Description Number 1 Switch Asssembly 5157201 2 Pump Head wSwitch Asssembly 5275064 3 Motor with connector no switch P39 045B Dimensions Inches mm 2 25 57 6 89 175 1 66 42 2 55 65 3 94 100 1 58 40 1...

Page 4: ...ine fuse and or fuse in car adapter end Ensure correct voltage 10 12 13 volt Low flow or no flow at all what should I check Check for a clogged suction hose and or suction strainer Often you will need to clean the suction strainer Check for proper voltage Is there a fuse for the sprayer Yes either an in line fuse a fuse located in the car adapter housing or both What size fuse should I use as a re...

Reviews: