background image

2

27

LIMITED WARRANTY

Worksaver warrants to the original purchaser of any new Pallet Fork (Models PF-448, SSPF-3748,

SSPF-3755, SSPF-3760, SSPF-442, SSPF-448, SSPF-5548, SSPF-5560, JDPF-5442, JDPF-5448,

JDPF-5460, JDPF-6748, JDPF-6760, JDPF-48048, JDPF-48060, GLPF-442, GLPF-448 and GLPF-

5548, GLPF-5560), that the equipment be free from defects in material and workmanship for a period of

six (6) months for non-commercial, state, and municipalities. Use sixty (60) days for commercial use from

date of retail sale.

Replacement or repair parts installed in the equipment covered by this warranty are warranted for sixty

(60) days from the date of purchase of such part or to the expiration of the applicable new equipment

warranty period, whichever occurs later.

Such parts shall be provided at no cost to the user during regular working hours. Worksaver reserves

the right to inspect any equipment or parts which are claimed to have been defective in material or

workmanship.

DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES

Worksaver’s obligation under this warranty, to the extent allowed by law, is in lieu of all warranties,

implied or expressed, including implied warranties of merchantability and fitness for a particular purpose

and any  liability for incidental and consequential damages with respect to the sale or use of the items

warranted. Such incidental and consequential damages shall include but not be limited to: transporta-

tion charges other than normal freight charges; cost of installation other than cost approved by

Worksaver; duty; taxes; charges for normal service or adjustments; loss of crops or any other loss of

income; rental of substitute equipment, expenses due to loss, damage, detention or delay in the deliv-

ery of equipment or parts resulting from acts beyond the control of Worksaver.

THIS WARRANTY SHALL NOT APPLY:

1. To vendor items which carry their own warranties, such as hydraulic cylinders, tires, and tubes.

2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.

3. If parts not made or supplied by Worksaver have been used in connection with the unit, if, in sole

judgement of Worksaver such use affects its performance, stability, or reliability.

4. If the unit has been altered or repaired outside of an authorized Worksaver dealership in a manner

which, in the sole judgement of Worksaver affects its performance, stability or reliability.

5. To normal maintenance service and normal replacement items such as bent forks, hydraulic fluid,

worn blades, or to normal deterioration of such things as belts and exterior finish, due to use or

exposure.

6. To expendable or wear items such as teeth, chains, sprockets, latch parts, springs and other items

that in the company’s sole judgement is a wear item.

NO EMPLOYEE OR REPRESENTATIVE OF WORKSAVER IS AUTHORIZED TO CHANGE THIS

WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN

WRITING AND SIGNED BY WORKSAVER’S SERVICE MANAGER, POST OFFICE BOX 100, LITCHFIELD,

ILLINOIS  62056-0100.

MODELS JDPF-H48048 & JDPF-H48060

PARTS LIST

Summary of Contents for PALLET FORK PF-448































Reviews:

Related manuals for PALLET FORK PF-448