PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
PR
OOF
STEP 1
STEP 2
STEP 4
STEP 3
© Office Star Products May 2017
PART QTY
1.
Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
2.
Casters . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
3.
Pneumatic Cylinder . . . . . . . . . . . . . . . . . . .1
4.
Bellows . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
5.
Seat Plate . . . . . . . . . . . . . . . . . . . . . . . . . .1
6.
Seat Cushion . . . . . . . . . . . . . . . . . . . . . . . .1
7.
Backrest . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
8.
Arms (8L & 8R) . . . . . . . . . . . . . . . . . . . . . 2
9.
Short Screw . . . . . . . . . . . . . . . . . . . . . . . . .6
10.
Long Screw . . . . . . . . . . . . . . . . . . . . . . . .6
11.
Plastic Cap . . . . . . . . . . . . . . . . . . . . . . . .4
12.
Allen Wrench . . . . . . . . . . . . . . . . . . . . . . .1
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
STEP 1
Insert five Casters (2) into Base (1), push hard until you feel or hear the Caster (2) snap into place. Insert Pneumatic Cylinder (3) into Base (1) and
slip Bellows (4) over Pneumatic Cylinder (3).
STEP 2
Attach Seat Plate (5) to Seat Cushion (6) with the arrow towards the front of the chair using two Short Screws (9) for rear of Seat Plate (5) and two
Long Screws (10) for front of Seat Plate (5).
FULLY TIGHTEN SCREWS USING ALLEN WRENCH (12).
STEP 3
Attach Arms (8L & 8R) to Seat Cushion (6) using two Long Screws (10) for each Arm (8).
DO NOT FULLY TIGHTEN SCREWS.
Secure Arms (8L & 8R) to rear of Backrest (7) using two Short Screws (9) for each Arm (8).
APPLY FIRM PRESSURE TO ALIGN & FULLY
TIGHTEN ALL SCREWS USING ALLEN WRENCH (12).
Cover holes in backrest using Plastic Caps (11).
STEP 4
Place the assembled seat on top of Pneumatic Cylinder (3) and apply downward pressure.
ATTENTION: MAKE SURE ALL SCREWS ARE FULLY TIGHTENED BEFORE USING CHAIR.
3
1
2
9
3
4
3
5
10
6
10
6
11
9
EMH69216 / EMH69217 / EMH6921C
SCREEN BACK MANAGER’S CHAIR
ASSEMBLY INSTRUCTIONS
