background image

Safety

14

 

− Only connect the compressor to an easily accessible socket so that you can 

quickly disconnect it from the power supply in the event of a fault.

 

− Lay the mains connection line so that it does not pose a tripping hazard.

 

− Do not kink the mains connection line and do not lay it over sharp edges.

 

− When not in use, before transport and before performing cleaning or 

maintenance, always pull the mains plug out of the socket.

 

− Do not use the compressor if the mains connection line or the mains plug 

is damaged. Have an authorised specialist workshop replace the dam-
aged part with an original part. To do so, contact the After Sales Support at 
the service address indicated on the warranty card.

 

− Operate the compressor with a residual current device (RCD) with a max-

imum release current of no more than 30 mA. Use of a residual current 
device (RCD) reduces the risk of electric shock.

 

WARNING!

Burn hazard!

The compactor and the lines of the compressor may become hot during opera-
tion. You could burn yourself on them.

 

− Do not touch the compactor and the lines during operation to avoid burns.

 

− Be careful when working.

 

WARNING!

Risk of injury!

The compressed air jet, which you generate with the compressor, has a high 
pressure. Improper use of the compressor or the compressed air jet poses a risk 
of injury!

 

− Do not point the compressed air jet or the pneumatic tools connected to 

the compressor at persons or animals.

 

− Do not use the compressed air jet to clean clothing being worn.

 

− Do not insert hands or objects through the compressor’s protective grates.

 

− Keep children and animals away from the functional area of the compressor.

 

− When separating the hose coupling, hold the coupling element firmly 

with your hand to prevent injury caused by the hose lashing back.

 

− When working with the compressor, wear protective goggles to protect 

yourself against debris and parts that are blown away.

Summary of Contents for GPAC2200





































Reviews: