background image

First use

16

First use

Checking the compressor and package contents

 

WARNING!

Risk of swallowing and choking!

Children must not play with plastic bags, wrappers and small parts. There is a 

risk of being swallowed and suffocation.

 

− Keep children away from the compressor, small parts and the packaging 

material.

 

− The compressor is not a children’s toy.

 

CAUTION!

Risk of injury!

The compressor is very heavy. You could damage yourself if you lift it out of the 

packaging by yourself.

 

− Do not lift the compressor by yourself, instead have another person help 

you lift it out of the packaging.

NOTICE!

Risk of damage

The compressor is already filled with oil when it is delivered to you. If you tip the 

compressor too much or place it on its side, oil could leak out and cause damage 

to property, contamination or similar. If you operate the compressor with not 

enough or no oil, you could damage the compressor as a result.

 

− Always hold the compressor in an upright position. Do not place it on its 

side for transport and to remove it from the packaging. 

 

− After unpacking and before each use, make sure that there is enough oil 

in the compressor.

1. Lift the compressor out of the packaging.

2. Place the compressor on a level, stable surface. 
3. Check to make sure that the delivery is complete (see 

Fig. A

 and 

B

).

4. Check whether the compressor or the individual parts exhibit damages. If this 

is the case, do not use the compressor. Contact the manufacturer at the service 

address specified on the warranty card.

Summary of Contents for GPAC2200





































Reviews: