WORLD DESIGNS WDHD3S Assembly Instruction Manual Download | Manualshive

Page: 5 / 11

background image

Fig. 3

Hardware Fittings (front panel)

Fig. 2

Hardware Fittings (rear panel)

WDHD3S Kit Assembly Instructions

4

Fit the output transformers to the chassis, using M4x10 screws, serrated
washers and nuts, positioning the secondary leads (blue x 4 and purple x
4) towards the outside of the chassis.

Fit the stand

-

offs for the PCB using M3x12 screws from the underside of

the chassis.

Fig. 3

Hardware Fittings (front panel)

Fig. 2

Hardware Fittings (rear panel)

WDHD3S Kit Assembly Instructions

4

Fit the output transformers to the chassis, using M4x10 screws, serrated
washers and nuts, positioning the secondary leads (blue x 4 and purple x
4) towards the outside of the chassis.

Fit the stand

-

offs for the PCB using M3x12 screws from the underside of

the chassis.

«
...
3
4
5
6
7
...
»

Summary of Contents for WDHD3S












Reviews:

No comments

Related manuals for WDHD3S

Brand: KAM Pages: 4

Brand: PROEL Pages: 39

Brand: Tascam Pages: 92

Brand: Sponsler Pages: 4

Brand: PA Tech Pages: 5

Brand: R&H Pages: 12

Brand: Ramsey Electronics Pages: 20

Smart MatriX SMX200

Brand: Analog way Pages: 4

Thunder 50 Type E322

Brand: Engl Pages: 6

Brand: C.E.C. Pages: 10

Brand: Thule Audio Pages: 2

Brand: Stageline Pages: 18

Brand: Banner Pages: 19

Brand: Blackstar Pages: 16

Acoustasonic 30

Brand: Fender Pages: 16

Brand: Audiovox Pages: 17

Brand: Technics Pages: 10

Brand: Gamut Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands