ECRESO FM 5kW / 10kW, user manual
–
11/2021
Page 113
WorldCast Systems SAS - 20 avenue Neil Armstrong - 33700 Mérignac (Bordeaux Métropole) FRANCE
+33 (0)5 57 928 928
–
www.worldcastsystems.com
–
contact@worldcastsystems.com
NAME
Access
(R/W)
Possible value on the serial
port of the unit
Comments
INPUT.LINE1.SW.THRESH
R/W
-
90…000
Silence triggering level in dBFS on channel 1
INPUT.LINE1.TRIM
R/W
-3.00 to 3.00
Sets the offset between left and right channels (+3 =
left channel level is 3 dBu higher than right channel
level)
INPUT.LINE1.TYPE
R
"ANA" or "AES" "OFF"
Indicates the type of audio signals present on input 1
INPUT.LINE2.ALARM
R/W
"NONE" or "FAULT" or
"WARNING"
Alarm generated upon loss of signal on the input
INPUT.LINE2.DRIVE
R/W
-6.00 to 6.00
Drive setting, allows an increase of the input audio level
without changing the deviation setting.
INPUT.LINE2.FLT
R/W
0;1;2 0=15;1=16;2=17
Configuration of the audio filter
INPUT.LINE2.GET_SAMPLING
R
0…200000
Gives the sampling rate in Hz
INPUT.LINE2.LEFT.PEAK
R
-
100 … 28
Gives the right audio input max peak value over 100
milliseconds
INPUT.LINE2.LEFT.PKMAX
R
-
100 … 28
Gives the right audio input max peak value over 1
second.
INPUT.LINE2.LEVEL
R/W
-20.00...18.00
Internal numerical gain. For AES, between -20 and 0; for
ANA between -18 and +18
INPUT.LINE2.LOST
R
"YES" or "NO"
Detection of silence on the input after timeout. If ‘Yes’,
an alarm may be sent depending on the setting for
INPUT.LINE2.ALARM.
INPUT.LINE2.PREAC
R/W
0;50;75
Sets the value of the pre-emphasis
INPUT.LINE2.PRESENCE
R
"NONE" or "L" or "R" or "L&R" Indicates audio signals are present on input 2
INPUT.LINE2.RIGHT.PEAK
R
-
100 … 28
Gives the right audio input max peak value over 100
milliseconds
INPUT.LINE2.RIGHT.PKMAX
R
-
100 … 28
Gives the right audio input max peak value over 1
second
INPUT.LINE2.SW.BACKDELAY
R/W
XXX=[0…30]
Back delay on the channel with the highest configurable
priority.
INPUT.LINE2.SW.NOSYNC
R/W
"ON" or "OFF"
If ON, switches on loss of AES synchro
INPUT.LINE2.SW.DELAY
R/W
XXX=[1…180]
Switching delay when loss of audio 2
INPUT.LINE2.SW.PRIO
R/W
0..7 ; 0=disabled
Priority of each audio channel (7= highest priority)
INPUT.LINE2.SW.SILENCE
R/W
"L" or "R" or "ANY" or "BOTH"
Sets on which channel silence detection must be
conducted for the audio input 2: L, R, L or R (ANY), L
and R (BOTH)
INPUT.LINE2.SW.THRESH
R/W
-
90…000
Silence triggering level in dBFS on channel 2
INPUT.LINE2.TRIM
R/W
-3.00 to 3.00
Sets the offset between left and right channels (+3 =
left channel level is 3 dBu higher than right channel
level)
INPUT.LINE2.TYPE
R
"ANA" or "AES" "OFF"
Indicates the type of audio signals present on input 2
INPUT.MPX.SW.BACKDELAY
R/W
XXX=[0…30]
Back delay on the channel with the highest configurable
priority.
INPUT.MPX.SW.DELAY
R/W
XXX=[1…180]
Switching delay when loss on the MPX input
INPUT.MPX1.ALARM
R/W
"NONE" or "FAULT" or
"WARNING"
Alarm generated upon loss of signal on the input
INPUT.MPX1.DRIVE
R/W
-6.00 to 6.00
Drive setting, allows an increase of the input audio level
without changing the deviation setting.
INPUT.MPX1.GET_SAMPLING
R
0…200000
Gives the sampling rate in Hz
INPUT.MPX1.LEVEL
R/W
-18.00...+18.00
Internal numerical gain
INPUT.MPX1.LOST
R
"YES" or "NO"
Detection of silence on the input after timeout. If ‘Yes’,
an alarm may be sent depending on the setting for
INPUT.MPX1.ALARM.
INPUT.MPX1.PEAK
R
-
150…150
Gives the deviation max peak value of the transmitted
signal in kHz over 100 milliseconds
INPUT.MPX1.PKMAX
R
-
150…150
Gives the deviation max peak value of the transmitted
signal in kHz over 1 second
INPUT.MPX1.PRESENCE
R
MO" or "MO+R" or "MO+R+S"
or "ST" or "ST+R" or "ST+R+S"
Gives the composition of MPX1 on channel 3. R = RDS ;
MO = Mono ; ST = Stereo ; S = SCA
INPUT.MPX1.SW.PRIO
R/W
0..7 ; 0=disabled
Priority of each audio channel (4= highest priority)
INPUT.MPX1.SW.THRESH
R/W
-
90…000
Silence triggering level in dBFS
