Operation—Monitor Operation
OUT4001,000071F -19-19JAN16-1/1
Main Menu—Radio
The
Radio
menu allows operator to set preferred radio
stations and adjust the tone settings.
The submenus under Main Menu that appear on monitor
include:
NOTE: Alarm List ONLY appears as a submenu
if there is an actual alarm.
•
Alarm List
•
Air Conditioner
•
Radio
•
Work Mode
•
Setting Menu
•
Information Menu
At Main Menu screen (1), rotate monitor dial (2) to
highlight Radio. Press monitor dial to display Radio menu.
Radio menu items include:
•
CH1 AM _ _ _ _ kHz
•
CH2 AM _ _ _ _ kHz
•
CH3 AM _ _ _ _ kHz
•
CH4 AM _ _ _ _ kHz
•
CH5 FM _ _ _ ._ MHz
•
CH6 FM _ _ _ ._ MHz
•
CH7 FM _ _ _ ._ MHz
•
CH8 FM _ _ _ ._ MHz
NOTE: Presetting memory radio stations can also be
done using the keypad (6) on switch panel. See
Operating the AM/FM Radio. (Section 2-1.)
Press radio tuning switch (5) to toggle between AM or
FM frequency. Tune radio to desired AM or FM station
by rotating the radio tuning switch. When desired station
is found, rotate monitor dial to highlight CH1. Press and
hold monitor dial for more than 1 second. Current station
is set. Repeat procedure for seven additional AM or FM
stations using CH2 through CH8. Once the stations are
stored, operator can select these programmed stations
by using keys 1—8 on the switch panel keypad (6).
•
<<
Rotate monitor dial to highlight <<. Press monitor dial
to seek next lower frequency station. Continue to press
monitor dial to seek next lower frequency station until
desired station is found.
•
>>
Rotate monitor dial to highlight >>. Press monitor dial to
seek next higher frequency station. Continue to press
monitor dial to seek next higher frequency station until
desired station is found.
•
TONE
Rotate monitor dial to highlight TONE. Press monitor
dial to adjust tone. Backlighting will turn orange. Rotate
monitor dial clockwise to boost treble. Rotate monitor
dial counterclockwise to boost base. Press monitor dial
again to store changes.
TX1086306A
—UN—28DEC10
Main Menu Screen
TX1086274A
—UN—27DEC10
Switch Panel
1— Main Menu Screen
2— Monitor Dial
3— Back Button
4— Home Button
5— Radio Tuning Switch
6— Keypad
•
AUTO PRESET
Rotate monitor dial to highlight AUTO PRESET. Press
monitor dial to start auto preset process. The AUTO
PRESET scans reception frequency and allocates
stations to CH1 to CH8. AM frequency stations will be
preset to CH1 to CH4 and FM frequency stations will be
preset to CH5 to CH8. Operating the radio during the
scan stops the AUTO PRESET process.
If an exclamation mark appears in the radio display on the
monitor, communication between the radio and the monitor
is abnormal. See an authorized John Deere dealer.
Press back button (3) to return to previous screen.
Press home button (4) to return to default screen.
2-2-13
092221
PN=88
Summary of Contents for 380GLC
