Miscellaneous—Machine
DX,TORQ1 -19-30MAY18-1/1
Unified Inch Bolt and Screw Torque Values
TS1671 —UN—01MAY03
SAE Grade 1
a
SAE Grade 2
b
SAE Grade 5, 5.1 or 5.2
SAE Grade 8 or 8.2
Bolt or Screw
Size
Hex Head
c
Flange
Head
d
Hex Head
c
Flange
Head
d
Hex Head
c
Flange
Head
d
Hex Head
c
Flange
Head
d
N·m
lb·in
N·m
lb·in
N·m
lb·in
N·m
lb·in
N·m
lb·in
N·m
lb·in
N·m
lb·in
N·m
lb·in
1/4
3.1
27.3
3.2
28.4
5.1
45.5
5.3
47.3
7.9
70.2
8.3
73.1
11.2
99.2
11.6
103
N·m
lb·ft
N·m
lb·ft
5/16
6.1
54.1
6.5
57.7
10.2
90.2
10.9
96.2
15.7
139
16.8
149
22.2
16.4
23.7
17.5
N·m
lb·ft
N·m
lb·ft
3/8
10.5
93.6
11.5
102
17.6
156
19.2
170
27.3
20.1
29.7
21.9
38.5
28.4
41.9
30.9
N·m
lb·ft
N·m
lb·ft
7/16
16.7
148
18.4
163
27.8
20.5
30.6
22.6
43
31.7
47.3
34.9
60.6
44.7
66.8
49.3
N·m
lb·ft
N·m
lb·ft
1/2
25.9
19.1
28.2
20.8
43.1
31.8
47
34.7
66.6
49.1
72.8
53.7
94
69.3
103
75.8
9/16
36.7
27.1
40.5
29.9
61.1
45.1
67.5
49.8
94.6
69.8
104
77
134
98.5
148
109
5/8
51
37.6
55.9
41.2
85
62.7
93.1
68.7
131
96.9
144
106
186
137
203
150
3/4
89.5
66
98
72.3
149
110
164
121
230
170
252
186
325
240
357
263
7/8
144
106
157
116
144
106
157
116
370
273
405
299
522
385
572
422
1
216
159
236
174
216
159
236
174
556
410
609
449
785
579
860
634
1-1/8
305
225
335
247
305
225
335
247
685
505
751
554
1110
819
1218
898
1-1/4
427
315
469
346
427
315
469
346
957
706
1051
775
1552
1145
1703
1256
1-3/8
564
416
618
456
564
416
618
456
1264
932
1386
1022
2050
1512
2248
1658
1-1/2
743
548
815
601
743
548
815
601
1665
1228
1826
1347
2699
1991
2962
2185
The nominal torque values listed are for general use only with the assumed
wrenching accuracy of 20%, such as a manual torque wrench.
DO NOT use these values if a different torque value or tightening procedure is
given for a specific application.
For lock nuts, for stainless steel fasteners, or for nuts on U-bolts, see the
tightening instructions for the specific application.
Replace fasteners with the same or higher property class. If
higher property class fasteners are used, tighten these to the
strength of the original.
•
Make sure that fastener threads are clean.
•
Apply a thin coat of Hy-Gard™ or equivalent oil under the head and on the threads of the fastener, as shown in the following image.
•
Be conservative with the amount of oil to reduce the potential for hydraulic lockup in blind holes due to excessive oil.
•
Properly start thread engagement.
TS1741 —UN—22MAY18
a
Grade 1 applies for hex cap screws over 6 in (152 mm) long, and for all other types of bolts and screws of any length.
b
Grade 2 applies for hex cap screws (not hex bolts) up to 6 in (152 mm) long.
c
Hex head column values are valid for ISO 4014 and ISO 4017 hex head, ISO 4162 hex socket head, and ISO 4032 hex nuts.
d
Hex flange column values are valid for ASME B18.2.3.9M, ISO 4161, or EN 1665 hex flange products.
4-1-19
092221
PN=204
Summary of Contents for 380GLC
