Operation—Operator's Station
Continued on next page
OUT4001,000073C -19-28FEB18-1/2
Switch Panel Functions
1. Back Button (for monitor use)—
Press button to
return to the previous menu.
2. Home Button (for monitor use)—
Press button to
return to the default screen when in any of the monitor
menus. If key switch is OFF, press and hold button to
check hour meter and fuel amount on monitor.
3. Monitor Dial (for monitor use)—
Press dial to go from
the default screen to the main menu screen. Rotate dial
to highlight desired menu function on the monitor. Press
dial to select desired screen information or to confirm
desired action.
4. Temperature Control/Mode Switch—
Press switch
to toggle between different air vent settings. The air
conditioner display on the monitor shows the different
settings each time the switch is pressed. There are four
different settings:
•
Air flows out of front vent and the defroster vents.
•
Air flows out of front, rear, and the defroster vents.
•
Air flows out of front, rear, foot, and the defroster vents.
•
Air flows out of foot vents.
Rotate switch counterclockwise for cooler air setting and
clockwise for warmer air setting. Temperature setting
will change on the air conditioner display as the switch
is rotated either way.
5. Blower Speed Switch—
If switch is pressed while air
conditioner is OFF, it turns to AUTO mode (blower speed
setting and air flow setting are selected automatically).
Temperature control/mode switch can be rotated to
operator's preferred cab degree setting. Blower speed
and air flow settings adjust automatically to reach and
maintain desired cab temperature.
If blower speed switch is rotated or temperature
control/mode switch is pressed while in AUTO mode,
AUTO mode is cancelled and all settings need to be
adjusted by the operator as needed.
If blower speed switch is pressed while air conditioner is
ON, it turns the air conditioner OFF. (This switch must be
ON to operate the ON/OFF function of the air conditioner
in the monitor menu.)
Rotate switch to adjust the blower speed to desired setting
when not in AUTO mode.
6. Radio Tuning Switch—
Press switch to toggle between
AM and FM frequency. Rotate switch to tune in desired
radio station.
7. Radio Power and Volume Switch—
Press switch to
turn radio on or off. Rotate switch to adjust the volume to
desired setting.
8. Engine Speed Dial—
Turn dial clockwise to increase
engine speed or counterclockwise to decrease engine
speed.
9. Auto-Idle Switch—
Turn switch to select between A/I
ON or A/I OFF.
With engine on, move auto-idle switch to A/I ON and
the engine speed dial to above the auto-idle speed.
Auto-idle indicator appears on monitor when auto-idle is
on. The engine runs at the engine speed dial setting for
4 seconds and then the auto-idle system will slow the
engine to auto-idle engine speed. When any control lever
is operated, engine speed increases to engine speed dial
setting. When control levers are placed back in neutral
position, auto-idle circuit automatically slows the engine to
auto-idle engine speed after 4 seconds.
Turn auto-idle switch to A/I OFF and set engine speed
dial to improve machine control in difficult work areas,
loading, and unloading. Auto-idle indicator disappears
on the monitor.
10. Travel Mode Switch—
Turn switch to select between
fast (rabbit) or slow (turtle) mode of travel.
11. Power Mode Button—
Press button to select different
engine speed modes:
•
ECO (economy) Mode—Use to improve fuel efficiency
and reduce noise level with a small difference in engine
speed.
•
PWR (power) Mode—Use when general digging work
is needed.
•
H/P (high power) Mode—Use when more flow is desired
for booming up or rolling in the arm in excavation work.
12. Work Light Switch—
Switch has three positions:
•
First Position—Drive light on base of machine turns
ON. Switch panel also illuminates.
•
Second Position—Boom work light turns ON along
with the drive light and switch panel. The monitor also
changes to night mode.
•
OFF—Work lights and switch panel illumination turns
OFF.
13. Windshield Wiper and Washer Switch—
Switch has
five operating positions:
NOTE: The wiper does not operate unless the upper
front window is completely closed.
•
OFF—Wiper stops operating and is retracted.
•
INT (slow)—Wiper operates intermittently at 8-second
intervals.
•
INT (medium)—Wiper operates intermittently at
6-second intervals.
•
INT (fast)—Wiper operates intermittently at 3-second
intervals.
•
ON—Wiper operates continuously.
Push and hold switch to spray fluid on windshield. If
switch is held more than 2 seconds, the wiper operates
until the switch is released. Do not hold down switch for
more than 20 seconds.
2-1-3
092221
PN=62
Summary of Contents for 380GLC
