20
2 in 1: Portable Power Cleaner/Water Sprayer
WG620E WG620E.X
TROUBLESHOOTING
Symptom
Possible causes
Solution
Machine turns on but it does not
draw any water or there is not
sufficient pressure.
Power nozzle is too high from the water
source surface.
Lower the machine below 5ft/1.5m.
Hose filter is blocked.
Take out the hose filter and rinse the
parts with clean water. (See Fig. Q1, Q2)
The users garden hose is not well
connected to the machine.
Check and reattach the garden hose
tightly. (See Fig. E1-E3)
Hose adapter looses.
The filter screen is missing. (See Fig.
E1 E2)
Tighten the hose adapter securely with
a spanner.
Contact WORX service agent to get a
filter screen.
Pump, hose, or other parts are frozen
due to outside temperatures.
Wait for the pump, hose or other parts
to thaw.
Hose kinks.
Straighten out the hose.
Multi-spray nozzle leaks.
The nozzle pattern does not spray
correctly.
Make sure the nozzle pattern symbol
aligns with the indicator mark on tool.
Fixing nail of the multi-spray nozzle
loosens.
Tighten it with a hex key.
Outlet pressure increases
suddenly.
Multi-spray nozzle is blocked.
Replace with a new multi-spray nozzle.
Machine drains out water after
stopping.
There is water remaining in the lance
and pump after stopping.
Drain all the water completely before
storage.
Soap accessory cannot spray
out any detergent.
Blockage in the soap bottle.
Clean it with fresh water.
Machine does not start.
The battery pack is not attached well.
Reinstall the battery pack.
Battery pack is empty.
Replace with a new battery pack or
recharge the battery pack.
Defective battery.
Replace with a new battery pack.
Machine pressure is not
consistent.
Additional air could be sucked into the
machine.
Check connection between the hose
adapter and the hose.
It is at low pressure setting.
No action need.
Machine stops automatically.
Battery pack is empty.
Replace with a new battery pack or
recharge the battery pack.
The multi-spray nozzle is blocked. The
current protection is activated.
Remove the multi-spray nozzle and turn
on the machine. If the machine works
normally, replace with a new multi-spray
nozzle.
Machine doesn’t self-priming
after being left unused for a
long time.
The machine sucked in air.
Connect the machine to the water
source first and then turn on.
Positec Australia Pty Limited
10 Corporate Blvd Bayswater, VIC 3153, Australia
Summary of Contents for HYDROSHOT WG620E
