Worx HydroShot WG629, Manual

Cordless Portable Power Cleaner 

EN

13

OPERATING INSTRUCTIONS

NOTE: 

Before using the tool, read the 

instruction book carefully.

ASSEMBLY & OPERATION

ACTION

FIGURE

BEFORE OPERATION

Installing the battery pack

See Fig. A1

Removing the battery pack

See Fig. A2

Charging the battery pack

More details can be found in WA3742’s 

manual

See Fig. A3

OPERATION 

NOTE: 

The power nozzle has two 

working modes: short lance only and 

pressure cleaning lance only.

Working mode 1

Attaching short lance to the power 

nozzle

NOTE: 

When attaching, align the 

two projections on the lance with the 

grooves of the power nozzle as shown 

in Fig. B.

NOTE: 

In this working mode, the 

pressure ranges from  1.5psi to 13psi. It 

is suitable for watering.

See Fig. B

Watering (working mode 1)

See Fig. C

Working mode 2

Attaching pressure cleaning lance to the 

power nozzle

NOTE: 

When attaching, align the 

two projections on the lance with the 

grooves of the power nozzle as shown 

in Fig. D. 

NOTE: 

In this working mode, the 

highest pressure is 320psi. It is suitable 

for removing strong stains.

See Fig. D

Attaching the multi-spray nozzle

NOTE:

 When attaching, rotating the 

nozzle left and right to make sure the 

nozzle fully seated into position and 

gently pulling it to make sure it is 

locked into position securely.

See Fig. E

Cleaning (working mode 2)

WARNING:

Do not connect the 

machine to water supplies 

that are dirty, rusty, muddy, or 

corrosive. (Including window 

cleaning liquids, plant foods, or 

fertilizers etc.)

NOTE:

 Not recommended for use 

with salt water, immediately rinse with 

fresh water for proper maintenance.

See Fig. F

Attaching the draw hose to the power 

nozzle

NOTE:

 After the draw hose is attached, 

check the connection by gently pulling 

upon the draw hose. It should not be 

pulled off.

See Fig. 

G1, G2

Attaching your own water hose 

(optional)

1. Attach the quick connect adapter

2. Attach the home garden hose with 

suitable connectors

NOTE: 

Except for the draw hose 

supplied, you can also connect the 

power nozzle to your own water hose 

with suitable connectors.

NOTE: 

Check whether the filter screen 

is missing before retightening the 

hose adapter. (Fig. S1, S2)  When 

retightening the hose adapter, please 

tighten securely. Otherwise, it may not 

draw any water for proper operation.

WARNING:

It is not 

recommended to connect the 

draw hose to your garden hose or 

your home tap.

See Fig. 

H, I

Pressure setting

Your power nozzle has two pressure 

modes. 

See Fig.  J

Start

NOTE: 

At the first use, you need to 

empty the air in hose, place the 

power nozzle below waist level (<5ft / 

1.5m), then attach the extension 

lance and set it at high pressure. Do not 

start working until the water 

goes up along the hose and sprays out. 

This could take up to 30 

seconds or more depending on the 

fresh water source.

See Fig. K

Selecting the nozzle pattern

NOTE: 

Choose a suitable nozzle 

pattern according to your work. Spray 

patterns 0

o

, 15

o

, 25

o

 and 40

o

 are 

applicable for cleaning, and the spray 

pattern with the symbol   is best 

suitable for showering.

WARNING: 

Do not shift the nozzle 

pattern when the tool is powered on.

See Fig. L