Worx WG165, Instructions Manual

13

12

2-in-1 Cordless Li-ion Grass Trimmer/Edger

EN

13

12

the main handle, apply adequate force to 
adjust, as shown in Fig H2.

9. SPaCER GuaRd  (See Fig i)

Push the flower guard in and out into place 
before trimming, as shown in Figure I. Make 
sure the flower guard is locked firmly in place.

oPErATIoN

waRNiNG:

 Always wear the eye 

protection. Never lean over the trimmer 

head. Rocks or debris can ricochet or be thrown 
into eyes and face and cause blindness or other 
serious injury. When operating unit, check for 
the following:
Wear eye protection and heavy clothing. Hold 
front handle with one hand and auxiliary handle 
with the other hand. Keep unit below waist 
level. Work only from your right to your left to 
ensure debris is thrown away from you. Without 
bending over, keep line near and parallel to the 
ground (perpendicular when edging) and not 
crowded into material being cut.

waRNiNG: make sure that line is 

fed out before operation. make sure 

motor is up to full speed before trimming 

or edging.

waRNiNG:

 Use only 0.065”(1.65mm) 

cutting line, diameter line. Other sizes of 

line will not feed properly and will result in 
improper cutting head function or can cause 
serious injury. Do not use other material 
such as wire, string, rope, etc. Wire can break 
off during cutting and become a dangerous 
projectile that can cause serious injury.

Trimming

Hold the bottom of the trimmer head about 
3.25”(8 cm) above the ground and at an angle. 
Allow only the tip of line to make contact. Do 
not force trimmer line into work area.

Edging (See Fig J)

Holding the lower housing then pull upwards 
the shaft, then rotate 90 degree clockwise. (Fig 
F1)
Adjust trimmer head angle to be the lowest 
horizontal setting. Then position the wheel on 
the ground for edge mode. The guard has two 
white line guides to indicate the cutting line 
position. Align these marks with the edge of 

your lawn.
While edging, allow the tip of the line to make 
contact. Do not force the line. The rotation 
wheel helps protect the unit and keeps the 
unit from contacting the ground. Take extra 
caution while edging as objects can be thrown 
from the trimmer line.

auTomaTiC LiNE FEEd SySTEm

When initially switching on the trimmer, a 
small length of line is fed out.
A ‘clattering’ noise will be heard when the 
lines hit the line cutter. DO NOT BE ALARMED 
this is quit normal. After about 5 seconds the 
line will be cut to the correct length and the 
noise will reduce as the motor receives full 
speed.
If the noise of the line being cut can’t be 
heard, more line will need to be fed out.
To feed more line, it is first necessary to allow 
the trimmer to stop completely, then restart, 
allowing the motor to reach full speed.
Repeat above until you hear the lines hitting 
against the line cutter. (Do not repeat this 
procedure more than 6 times)

To maNuaLLy FEEd THE LiNE (See Fig 

k1)

If required, line can be feed out manually
To operate, press and release manual line feed 
button (16), while gently pulling out the line 
until it is long enough to reach the line cutter.
If the line extends past the line cutter, too 
much line has been fed out.
If too much line is fed out, remove the spool 
cap and turn spool counter-clockwise until the 
line is at the desired length.

To REmovE THE CaP  (See Fig k2)

Press and hold in the two latches (12).
Pull cap away from the spool holder
When refitting the spool cap.
Keep all areas of the cap and spool holder 
clean.
Replace the cap, pressing firmly down 
towards the spool holder to ensure cap is fully 
located into position.
Check that the cap is correctly fitted by trying 
to remove it without depressing the two 
latches.