Attachment-Capable String Trimmer EN
14
ASSEMBLY & OPERATION
NOTE:
Before using the tool, read the
instruction book carefully.
Action
Figure
Assembly
Assembling the Trimmer Shaft
Insert the screw into the hole, then
tighten the locking knob
See Fig. A
Assembling the Auxiliary Handle and
Safety-stop Handle
See Fig. B1,
B2
Assembling the Safety Guard
Insert the metal bracket into the slot
on the safety guard, then secure the
guard in place using the screw and
hex key.
See Fig. C
Assembling the Shoulder Strap
See Fig. D
Installing and Removing the Battery
Pack
NOTE:
• This machine will only run
when 2 batteries are installed. It
is recommended to use the same
two batteries and charge the
two batteries at the same time.
• When two batteries are used
with different amp hours or
charge level, the machine will
run to the lowest common
denominator.
* It is recommended that using
4.0Ah or above battery pack for
better performance and longer
run time.
See Fig.
E1, E2
Checking the battery charge
condition
NOTE:
Fig. E3 only applies for the
battery pack with battery indicator
light.
See Fig. E3
Charging the battery pack
NOTE:
• The batteries are shipped
uncharged. Each battery must be
fully charged before the first use.
• Always fully charge the two
batteries at same time. More details
can be found in charger’s manual.
See Fig. E4
Battery power indicator on the
machine
See details in BATTERY STATUS
section
See Fig. E5
Operation
To start
WARNING!
The cutting head
continues to rotate after the
trimmer has been switched off; wait
until it has completely stopped then
lay down the tool.
Press the lock-off button first, then
press the switch trigger to start the
machine.
See Fig. F
ECO Speed
For longer run time, press the ECO
button and switch trigger, then your
machine will operate at a low speed.
See Fig. G
Trimming
See Fig. H
Bump feed
See Fig. I
Assembling and removing the
trimmer head
Insert the hex key into the hole and
rotate the trimmer head until it stops
in a locked position. Then, rotate
counterclockwise to remove it, and
clockwise to assemble it.
See Fig. J
Winding the trimmer line
NOTE:
The spool must be wound
while inside the trimmer head. The
spool cannot be wound with line,
then installed into the trimmer head.
See Fig.
K1, K2
Assembling the brush cutter blade
Remove the trimmer head and the
skirt before assembling the brush
cutter blade.
Insert the hex key into the hole.
Place the brush-cutter blade on top
of the spacer, place washer on top of
the brush-cutter blade, place blade
housing over washer. After that, use
the wrench to tighten the lock-nut.
See Fig. L1,
L2, L3
Cutting
See Fig. M
ATTACHMENT-CAPABLE ACCESSORIES
The below attachment accessories are sold
separately to convert the grass trimmer into a tool
for various applications.
1. Pole hedge trimmer attachment (WA0220)
This attachment is intended for cutting and
trimming hedges and bushes in domestic use.
2. Pole saw attachment (WA0222)
This attachment is intended for sawing of trees,
tree trunks, branches, limbs, etc. Cuts can be
sawed with or across the grain. This product is
not suitable for sawing mineral materials.
3. Edger attachment (WA0223)
This attachment is intended for edging around
walkways, driveways, flower beds, etc.
Summary of Contents for WG186E
