Lawn mower
En
11
10
11
10
ASSEMBLy
IMPORTaNT!
Before you assemble
the lawn mower, check the accessories
according above information, make sure the
accessories are completed.
FITTING THE LOwER HaNDLE.(See a, b,
C, D)
The mower should now look like fig A. Fix
the lower handle brackets (17) to the deck
as fig B and align the handle as fig C. Make
sure that they are located properly before
inserting the lower handle knobs and tighten
clockwise.(See D) Lift the Upper handle into
position as shown E. align handle and tighten
handle knob clockwise. Check that the upper
and lower handles are firmly secure. Ensure
the cables do not become stuck when folding/
unfolding Lower Handle.
NOTE:
Ensure that the cable clips (14)(See
E) supplied are used to fix the cable to the
Lower Handle
(15).(See B) Attach the cable
clips and make sure there is enough cable
slack.
GRaSSbOx HaNDLE aSSEMbLy (See
F.1)
First connect the grass box handle (10) to the
box top using the four provided screws.
DO NOT OVER TIGHTEN THE SCREWS.
GRaSSbOx aSSEMbLy (See F.2 and G)
Next, snap together the top and bottom grass
box halves by pushing all the “snap fits”
together around the edges; start from the rear
and work towards the front.
GRaSS bOx
FITTING
Lift the safety flap (9) and insert grass box
(8).(See H)
As the grassbox fills up, grass will be clearly
visible through the inspect window(18)(See I)
When the window is full it its time to empty
the grassbox.
REMOVING/EMPTyING
Lift the safety flap (9) and hold up. Remove
grass box (8)
MuLCHING FEaTuRE
For non-grass collection, the mower can be
used without the grass box (8) in position,
with the safety flap (9) in the down position.
waRNING!
Always check the safety
flap can close the discharge outlet
tightly before using. Never lift the safety
flap (9) when the lawn mower is being used
without fitted grass box.
OPERATIOn
STaRTING aND STOPPING (See J)
STaRTING
Connect the female extension cable connector
to the pigtail (See J).Connect the plug to the
mains an switch ON.
The switchbox is provided with a lock-
off button to prevent accidental starting.
With one hand press and hold the safety
button (2),with the other hand squeeze the
switch lever (1) towards the handle,and
release the safety lock off button.The machine
is now started ,wait until the product is at full
speed before cutting the grass.
Then Use both your hands to hold the switch
lever to keep it running.
STOPPING
Release the switch lever (1).
aDJuSTING THE CuTTING HEIGHT (See
K)
waRNING!
before adjusting the
mower height, wait for the mower
to completely stop. Mower blades
continue to rotate after the machine
is switched off and a rotating blade
can cause injury. wait until all machine
components have completely stopped
before touching them.
Before your first cut, adjust the mower cutting
depth to the desired position The mower
can be set to one of six cutting heights, with
cutting heights between 20 mm and 70 mm.
To adjust the cutting height press the height of
cut lever (6) outwards ,at the same time lifting
or pushing down the mower until required
height is selected.
Summary of Contents for WG711E
