18
Cordless Lawn Mower
EN
WEAR PROPER EYE PROTECTION WHILE
REMOVING, SHARPENING, AND INSTALLING
BLADE. ENSURE THAT SAFETY KEY IS REMOVED.
Sharpening the blade twice during a mowing season
is usually sufficient under normal circumstances.
Sand causes the blade to dull quickly. If your lawn
has sandy soil, more frequent sharpening may be
required.
REPLACE BENT OR DAMAGED BLADE
IMMEDIATELY.
WHEN SHARPENING THE BLADE:
1. Make sure blade remains balanced.
2. Sharpen blade at the original cutting angle.
3. Sharpen cutting edges on both ends of blade,
removing equal amounts of material from both
ends.
Note:
1. Be sure the mower is turned off and remove
the key.
2. Place the mower in stand up storage mode.
TO SHARPEN BLADE IN A VISE (SEE Fig. N1)
1. Be sure the switch lever is released, the blade
has stopped and the safety key removed before
removing the blade.
2. Remove blade from mower. See instructions for
removing and attaching blade.
3. Secure blade N1-1 in a vise N1-2.
4. Wear safety glasses and be careful not to cut
yourself.
5. Carefully file the cutting edges of the blade with a
fine tooth file N1-3 or sharpening stone.
6. Check balance of blade. See instructions for blade
balancing.
7. Replace blade on mower and tighten securely.
Refer to instructions below.
BLADE BALANCING (SEE Fig. N2)
Check balance of blade by placing center hole in
blade N2-1 over a nail or screwdriver shank N2-2,
clamped horizontally in a vise N2-3. If either end of
the blade rotates downward, file that end. Blade is
properly balanced when neither end drops.
BLADE MAINTENANCE (See Fig. O1, O2)
Renew your metal blade after 50 hours mowing
or 2 years, which ever is the sooner-regardless of
condition.
Follow these procedures to remove and replace the
blade. You will need garden gloves (not provided)
and a spanner wrench (not provided) to remove the
blade. Hold the blade(19) and unscrew the blade
bolt(18) counter-clockwise using a spanner wrench,
and then remove blade.
To re-assemble, position the blade(19) with the
cutting edges towards the ground. Then securely
tighten the blade bolt(18) .
STORAGE (SEE Fig. M1, M2)
Stop the mower and always remove the safety key.
Clean the exterior of the machine thoroughly using
a soft brush and cloth. Do not use water, solvents
or polishes. Remove all grass and debris, especially
from the ventilation slots.
Turn the machine on its side and clean the blade
area. If grass cuttings are compacted in the blade
area, remove with a wooden or plastic implement.
Store the machine in a dry place. Do not place other
objects on top of the machine.
To aid storage, release the Lock Cam Lever, and fold
the upper handle as shown in Fig. M1, M2.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be disposed
of with household waste. Please recycle where
facilities exist. Check with your local authorities
or retailer for recycling advice.
Summary of Contents for WG744E
