Worx WG787, User Manual

15

14

3-in-1 Cordless Lawn Mower            

EN

15

14

charging is complete (approximately 10-12 
hours to charge a fully discharged battery)

6.  After the battery is fully charged the green 

light will turn on and charge it on for 15 
seconds to indicate a full charge. After 15 
seconds the green light and charges will 
turn off to save power.

Note: if the battery is defective, the 

red light on the charger will flash.

The red and green lights will only 

function when the charger is 

connected to both the battery and 

wall receptacle.

7.   The charger is a smart charger and can 

stay connected to the battery and wall 
receptacle for extended periods of time 
without fear of damaging the battery or 
charger. The charger will automatically 
turn on and off periodically to ensure the 
battery is fully charged.

BATTERY CARE

The battery in your cordless lawnmower is a 
24-volt sealed lead acid system. The battery 
can be stored in any position without fear of 
leakage.
•  For optimal battery life and performance 

the battery should be fully charged every 2 
months during storage.

•  For optimal battery life and performance 

the battery should be fully charged after 
each use.

•  Store the battery in a cool dry location.
•  The battery can be safely stored down to 

14°F (-10°C).

•  The battery does not need to be fully 

discharged before recharging.

•  Initially 2 to 3 charging cycles may 

be required after purchase to achieve 
maximum run time capacity.

The battery is maintenance free. ADDITIONAL 
BATTERIES can be obtained from the 
Customer Helpline 1-866-354-9679.

ASSEMBLY

iMPorTaNT! 

Before you assemble 

the lawn mower, check the accessories 

according to the information, make sure the 
accessories are complete.

1. FiTTiNG ThE haNDLE (See Fig.B1- B5)

1)  Remove the screws (b) on the both side of 

deck. (Fig B1)

2)  Insert the lower handle (8) into the holes on 

the deck provided. Be sure to carefully align 
the screw holes found on the lower handles 
with the screws holes found on the deck 
(b). (See Fig B1, B2) 

3)  Secure the lower handle bars to the deck 

with the screws (b) provided. (See Fig B2)

4)  Attach the upper handle (6) with the bolts 

and lock cam lever (7) to the lower handle 
(8). (Fig B3)

5)  Tightening the two Lock cam levers. Check 

that the handle is FULLY secured.

  The cam lever pressure can be adjusted 

by rotating the lock cam lever (7) or (8) 
clockwise/counter-clockwise. DO NOT OVER 
TIGHTEN.(Fig. B4) 

NoTE: 

Ensure the bolts are fully inserted 

through the handles before adjusting or 
tightening the cam levers.

6)  Attach the cable clips (2) provided, to the 

upper and lower handle. Insert the cable 
into the clips ensuring there is enough 
cable slack. (Fig B5)

2. GraSS CoLLECTioN BaG aSSEMBLy

1)  Attach the grass bag handle to the grass 

bag assembly as shown in F ig C1-C4.

a.  Identify the front and rear of both the 

handle and the grass bag assembly. 

  (Fig C1)
b.  Insert the front (I) portion of the handle into 

position. (Fig C2)

c.  Secure the front portion of the handle in 

place by pushing the front portion of the 
handle forward (II). (Fig C2)

d.  Insert and secure the rear portion of the 

handle in position by pushing down on the 
back (III) of the handle ensuring it “clicks” 
into position. (Fig C2) 

2) Clip the plastic clips of the grass bag over 

the metal frame. (Fig C3)  

warNiNG: Make sure to not fit the 

handle in the reverse direction as it 

will not remain secure.  Make sure to fit