2-in-1 Grass Trimmer/Edger
EN
15
14
WARNING!
Always wear the eye protection.
Never lean over the trimmer head. Rocks or
debris can ricochet or be thrown into eyes and face
and cause blindness or other serious injury. When
operating unit, check for the following:
Wear eye protection and heavy clothing. Hold front
handle with one hand and auxiliary handle with the
other hand. Keep unit below waist level. Work only
from your right to your left to ensure debris is thrown
away from you. Without bending over, keep line
near and parallel to the ground (perpendicular when
edging) and not crowded into material being cut.
WARNING!
Make sure that line is fed out
before operation. Make sure motor is up to
full speed before trimming or edging.
WARNING!
Only use 1.65mm diameter
cutting line.
Other sizes of line will not feed
properly and will result in improper cutting head
function or can cause serious injury. Do not use other
material such as wire, string, rope, etc. Wire can break
off during cutting and become a dangerous projectile
that can cause serious injury.
ASSEMBLY & OPERATION
Action
Figure
Assembly
Assembling the Safety Guard
See Fig. A1, A2
Mounting the Edger Wheel
WARNING: Make Sure the
ON/OFF Switch is Locked
Off to Prevent Accidental
Starting.
See Fig. B
Installing and Removing the Battery
Pack
See Fig. C
Charging the battery pack
More details can be found in
charger’s manual
See Fig. D1, D2
Checking the battery condition
Note:
Fig. D3 only applies for the
battery pack with battery indicator
light.
See Fig. D3
Operation
Safety ON/OFF Switch
WARNING!
The cutting head
continues to rotate after the
trimmer has been switched off;
wait until it has completely stopped
then lay down the tool.
See Fig. E
Trimming
- Adjusting the Shaft
WARNING!
Make Sure the
ON/OFF Switch is Locked Off
to Prevent Accidental Starting.
See Fig. F
- Adjusting the Trimmer Head
See Fig. G1, G2
- Adjusting the Auxiliary handle
See Fig. H
- Trimming
See Fig. I1
- Using the Flower Guard
See Fig. I2
Edging
- Changing the tool into the Edging
mode
See Fig. J1, J2
- Edging
See Fig. K
Command feeding the line
- Note: Press as needed.
See Fig. L
Manually feeding the line
See Fig. M
Replacing the trimmer Spool
See Fig. N1, N2,
N3
Manually winding the line
See Fig. O1, O2,
O3, O4
WORKING HINTS
1. AUTOMATIC LINE FEED SYSTEM
When initially switching on the trimmer, a small length
of line is fed out.
A ‘clattering’ noise will be heard when the lines hit the
Line Cutter. DO NOT BE ALARMED. This is quite normal.
After about 5 seconds the line will be cut to the correct
length and the noise will reduce as the motor gains
full speed.
If the noise of the line being cut can’t be heard, more
line will need to be fed out.
To feed more line, it is first necessary to allow the
trimmer to stop completely; it must come to a
complete rest, then restart, allowing the motor to
reach full speed.
Repeat above until you hear the line hitting against the
Line Cutter.
2.
(See Fig. L)
Your grass trimmer is equipped with a Command Feed
System. Just press the button while the machine is
running, new line will feed out and then stop when
you hear the ‘clattering’ noise of the new line being
cut. The motor stops briefly when the Command Feed
button is pressed, and restarts when released. This
Summary of Contents for WP165E
