Worx WX858.9, Quick Start Manual

9

20V Cordless random orbital waxer/polisher

EN

ACCESSORIES

WX858.9

Wool bonnet

1

Terry cloth bonnet

1

We recommend that you purchase your accessories 

from the same store that sold you the tool. Refer to 

the accessory packaging for further details. Store 

personnel can assist you and offer advice.

OPERATING 

INSTRUCTIONS

NOTE: 

Before using the tool, read the 

instruction book carefully.

Intended Use

The machine is intended for polishing floor, car and 

other coated surfaces.

1. INSTALL/REMOVE THE BATTERY PACK 

To install: Place the switch in the OFF (O) position. 

Then, slide the battery pack into the polisher. (See 

Fig.A1)

To remove: Place the switch in the OFF (O) position. 

Then, press the button to remove the battery pack 

from the polisher. (See Fig.A2)

2. ON/OFF SWITCH (SEE FIG.B)

Always start and stop the polisher against the car 

surface. Slide switch to the ON (I) position to start 

the polisher, pull backward to OFF (O) position to 

stop it.

3. Polishing
3.1 Place the polishing bonnet (wool bonnet) 

over the sponge pad (see Fig. C) (If no 

polishing is needed, proceed with waxing 

directly (4). Ensure the car is washed clean 

before polishing or waxing

Set the switch to OFF (O) position and remove the 

battery pack. Place the polishing bonnet (wool 

bonnet) over the sponge pad and always make 

sure that its elastic strip is securely adhered to the 

sponge pad. 

3.2 

Spread the polish (car wax) 

Spread about a teaspoonful of polish (car wax) 

evenly over the surface of the pad cover. Do not 

apply polish (car wax) directly to the car. 

Most polish (car wax) is either a paste or liquid 

form. Read all instructions for proper application 

and use before operation 

Spread polish paste (see Fig. D1)

Spread about a teaspoonful of polish evenly over 

the waxing bonnet using a putty knife or other tool 

with a broad flat blade. Do not apply it directly to 

the surface to be polished. 

Apply liquid polish (see Fig. D2)

Spread a small amount of polish in the size of about 

half a coin around the center of the waxing bonnet 

and then apply it in a circle, with each circle slightly 

larger than the previous one. 

Note:

 Do not apply too much polish at once. 

Having it fully soaked will affect the duration and 

effectiveness of the polish. 

3.3 

Polish with the car polisher

Hold the polisher against the surface and slide the 

ON/OFF switch to the ON (I) position. First, use wide 

sweeping strokes to polish larger surfaces such as 

the front hood, trunk and roof. Do not apply excess 

pressure on the polisher. After covering the plane 

surfaces, polish the curved surfaces such as car 

doors in cycles. When done with the entire surface, 

turn off the polisher. Lift the polisher off from the 

surface only after the sponge pad stops rotating.

(See Fig. E1)

Note: 

It is also convenient to polish the car roof 

and side panels by one hand.

 (See Fig. E2)

Polishing a smaller surface area (see Fig. E3) 

For hard-to-reach areas such as bottom of the 

bumpers or the side mirrors, polish them by hand. 

Wipe off the residual powder with clean towel after 

finishing polishing. 

4. Waxing

4.1 

Place the waxing bonnet (terry-cloth bonnet) 

over the sponge pad (see Fig. F) 

Place the waxing bonnet (terry-cloth bonnet) over 

the sponge pad and always make sure that its 

elastic strip is securely adhered to the sponge pad. 

4.2 

Repeat steps 3.2 to 3.3 to finish waxing evenly. 

5. BUFFING AND POLISHING - REMOVING 

THE WAX FROM THE SURFACE (SEE FIG. G)

NOTE: 

Wait until wax has dried to an even haze on 

vehicle. Remove wax in the same order in which it 

was applied.

Turn the polisher to the ON position. Polish and buff 

the entire surface until all dried wax is removed. 

Remove the bonnet from time to time and shake 

out the residue. The bonnet with excess residue 

will cause streaking. You may need to replace the 

bonnet if you can't get it clean enough to avoid 

streaking. Final buffing and polishing use a clean 

bonnet. 

NOTE: For best results, use long, sweeping strokes 

in a criss-cross pattern when removing wax.

WORKING TIPS FOR YOUR 

POLISHER

1.  For best results, the surface should be clean and 

dry. Most high-gloss surfaces can be cleaned 

with mild soap and water solution. To remove