background image

Rev 1.0/2-17 

#35204 

LIMITED WARRANTY 

 

Powr-Grip products are carefully constructed, thoroughly inspected at various stages of 

production, and individually tested.  They are warranted to be free from defects in workmanship 
and materials for a period of one year from the date of purchase. 
If a problem develops during the warranty period, follow the instructions hereafter to obtain 

warranty service.  If inspection shows that the problem is due to defective workmanship or 
materials, Powr-Grip will repair the product without charge. 
 

WARRANTY DOES NOT APPLY WHEN: 

Modifications have been made to the product after leaving the factory. 

Rubber portions have been cut or scratched during use. 

Repairs are required due to abnormal wear and tear. 

The product has been damaged, misused, or neglected. 

 
If a problem is not covered under warranty, Powr-Grip will notify the customer of costs prior to 

repair.  If the customer agrees to pay all repair costs and to receive the repaired product on a 

C.O.D. basis, Powr-Grip then will proceed with repairs. 

 

Wood's Powr-Grip Co., Inc. 

908 West Main St. / P.O. Box 368 

Laurel, MT  USA  59044 

 

phone  800-548-7341 
phone  406-628-8231 

fax  406-628-83

TO OBTAIN REPAIRS OR WARRANTY SERVICE 

For purchases in 

North America: 

Contact the Technical Service Department at Wood’s Powr-Grip Co.  When factory service 

is required, ship the complete product--prepaid--along with your name, address and 
phone number to the street address hereafter. 

For purchases in 

all other localities: 

Contact your dealer or the Technical Service Department at Wood’s Powr-Grip Co. for 

assistance. 
 

 

Summary of Contents for MRTA8











Reviews: