background image

Rev 10.3/10-16 

36 

MTCL8FS10TDC: #35079 

REPLACEMENT PARTS LIST 

 

Stock No. 

Description 

Qty. 

93220 

Dynaflo Vacuum Pump - Diaphragm Type - 1-SCFM [28 liters/minute] - 12 V DC  (Dynaflo ) 

66197BM 

Dynaflo Pump Gasket & Flap Valves 

66197AM 

Dynaflo Pump Diaphragm Kit 

66197 

Dynaflo Pump Head Assembly 

65442AM 

Vacuum Hose - 1/4" [6.3 mm] ID x 48" [122 cm] Length - Coiled - Green 

65441 

Vacuum Hose - 1/4" [6.3 mm] ID x 48" [122 cm] Length - Coiled - Red 

65440 

Vacuum Hose - 1/4" [6.3 mm] ID - Red  (approx. 100" [254 cm] in length) 

65437 

Vacuum Hose - 1/4" [6.3 mm] ID - Green  (approx. 100" [254 cm] in length) 

65429 

Vacuum Hose - 0.16" [4.1 mm] ID - Blue  (approx. 70" [178 cm] in length) 

65253 

Solenoid Valve - 12 V DC - 8 W 

65244 

Solenoid Valve - 12 V DC - 5 W  (for vacuum reserve tanks) 

65211 

Check Valve - 1/8 NPT - 0.5 psi 

65010 

Pad Spring - Coil Type  (for VPFS10T pads) 

64752 

Audio Alarm - 5-15 V DC - Panel Mount  (for low vacuum warning buzzer) 

64713AM 

Battery Charger - 240 V AC - Australian Type 

64712AM 

Battery Charger - 120 / 120 V AC 

64711AM 

Battery Charger - 240 V AC 

64682 

Battery - 1.5 V DC - AA Alkaline  (for optional radio transmitter) 

64670 

Battery - 12 V DC - 35 Amp-Hours 

64590 

Battery Gauge 

64461 

Circuit Breaker - 10 A  (for vacuum pumps) 

64459 

Circuit Breaker - 5 A  (for vacuum controls and indicators) 

64283 

Bulb - 13 V - Bayonet  (for vacuum lift lights) 

64271 

Strobe Light - 12 V DC - Amber  (option) 

64262 

Green Lens  (for vacuum lift light on power system enclosure) 

64238AA 

Vacuum Switch - 1/8 NPT - Digital w/Dual Set Point 

64213 

Push-Button Switch - Chrome  (for apply, enable, and release buttons) 

64200AM 

Push-Button Switch w/Integrated Green Light  (for movable control pendant) 

64199 

Push-Button Switch  (for battery test button) 

64191 

Contact Block  (for power switch) 

58382 

Remote Control System Retrofit Kit  (option) 

49724TT 

Sealing Ring Insert - Model VIFS10T2 - Closed Cell Foam  (for VPFS10T pads) 

49724LT 

Sealing Ring Insert - Model VIFS10T1 - Low-Marking Rubber  (for VPFS10T pads) 

49672T 

Vacuum Pad - Model VPFS10T / 10" [25 cm] Diameter - w/Replaceable Sealing Ring 

49150 

End Plug - 2 1/2" x 2 1/2" x 1/4" [63.5 mm x 63.5 mm x 6.4 mm] Tubing Size 

49122 

End Plug - 2" x 2" x 1/4" [50.8 mm x 50.8 mm x 6.4 mm] Tubing Size 

12 

29353 

Pad Cover 

20050 

Pad Ring Installation Tool 

16132 

Filter Element Kit  (for 4.4 oz [130 ml] bowl size air filter) 

16057 

Quick Connector - 1/8 FNPS - Male End 

12 

16056 

Quick Connector - 1/8 FNPS - Female End 

12

 

15910 

Vacuum Gauge - 2" [5.1 cm] Diameter - 1/8 NPT - CBM Type 

15791 

Control Handle 

15632 

Pad Filter Screen - Small  (for VPFS10T pads) 

8

 

13530 

Cotterless Hitch Pin - 1/2" x 3-1/2" [12 mm x 89 mm] 

12

 

10904 

Shoulder Bolt - Socket Head - 5/16" X 1" X 1/4-20 Thread  (for mounting pads) 

48 

SERVICE ONLY WITH IDENTICAL REPLACEMENT PARTS, 

AVAILABLE AT WPG.COM OR THROUGH AN AUTHORIZED WPG DEALER 

Summary of Contents for MTCL8FS10TDC















































Reviews: