WPI A310 Accupulser Instruction Manual Download

Page: 2 / 21

A310 Accupulser™ Pulse Generator

World Precision instruments

Copyright © 2001 by World Precision Instruments, Inc. All rights reserved. No part of this publication may be
reproduced or translated into any language, in any form, without prior written permission of World Precision
Instruments, Inc.

CONTENTS

INTRODUCTION.............................................................................................................................1

SAFETY..............................................................................................................................................2

PREPARATION.FOR.USE..............................................................................................................4

Shipping.Information.........................................................................................................4

Installation.............................................................................................................................4

Line.Fuse.................................................................................................................................5

Tilt.Bail....................................................................................................................................5

Rack.Mounting.....................................................................................................................5

CONTROLS,.INDICATORS.&.CONNECTORS.........................................................................6

Front.Panel............................................................................................................................6

Rear.Panel..............................................................................................................................9

OPERATING.DIRECTIONS.........................................................................................................10

Pulse.......................................................................................................................................10

Train.......................................................................................................................................13

MAINTENANCE.............................................................................................................................15

Cleaning................................................................................................................................15

Test.........................................................................................................................................15

SPECIFICATIONS...........................................................................................................................17

WARRANTY...................................................................................................................................18

Summary of Contents for A310 Accupulser






















Search results

Summary of Contents for A310 Accupulser

Reviews:

Related manuals for A310 Accupulser

Brands by name

Popular brands

WPI A310 Accupulser, Instruction Manual

Search results

Summary of Contents for A310 Accupulser

Reviews:

Related manuals for A310 Accupulser

Brands by name

Popular brands